Yamaha YZF-R6 Скачать руководство пользователя

Страница: 388 / 425

8-32

Battery positive terminal

white / yellow

(white /green)

Battery negative terminal

black

Headlight

Tester positive probe

yellow

or green

Tester negative probe

black

High beam indicator light

Tester positive probe

yellow

Tester negative probe

black / blue

Meter assembly coupler (wire harness side)

Set the main switch to “ON”.

Set the light switch to “

”.

Set the dimmer switch to “

” or “

”.

Measure the voltage (12 V) of yellow (green)

on the headlight coupler (headlight side).

Is the voltage within specification?

YES

Replace the meter
light bulb, socket or
both.

4. Headlight relay (Hi or LO)

Disconnect the headlight relay from the cou-
pler.

Connect the pocket tester (

Ω

1) and bat-

tery (12 V) to the headlight relay terminals as
shown.

Tester positive probe

yellow ( green)

Tester negative probe

red / yellow

YES

Replace the head-
light relay.

Does the headlight relay have continuity be-
tween yellow (green) and red / yellow?

This circuit is OK.

EB805411

2. Illumination fails to come on.

1. Meter light bulb and socket.

Check the meter light bulb and socket for
continuity.
Refer to “CHECKING THE BULBS AND
BULB SOCKETS”.

Are the meter light bulb and socket OK?

The wiring circuit
from the main switch
to the headlight cou-
pler is faulty and must
be repaired.

YES

2. Voltage

Connect the pocket tester (20 V) to the meter
assembly coupler (wire harness side) as
shown.

Tester positive probe

blue

Tester negative probe

black / blue

LIGHTING SYSTEM

ELEC

Содержание YZF-R6










































































































































































































































































































































































































































Результаты поиска

Содержание YZF-R6

Отзывы:

Похожие инструкции для YZF-R6

Бренды по названию

Популярные бренды

Yamaha YZF-R6, Руководство по обслуживанию

Результаты поиска

Содержание YZF-R6

Отзывы:

Похожие инструкции для YZF-R6

Бренды по названию

Популярные бренды