Yamaha YZF-R6 Скачать руководство пользователя страница 20

Страница: 20 / 425

1-9

SPECIAL TOOLS

GEN

INFO

Tool No.

Tool name / Function

Illustration

90890-01426

Oil filter wrench

This tool is needed to loosen or tighten the oil
filter cartridge.

90890-01434

Rod holder

This tool is used to support the damper ad-
justing rod.

Rod puller
90890-01437
Rod puller
attachment
90890-01436

Rod puller
Rod puller attachment

These tools are used to pull up the front fork
damper rod.

90890-01441

Fork spring compressor

This tool is used to disassemble or assemble
the front fork legs.

Fork seal driver
90890-01376
Fork seal driver
attachment
90890-01374

Fork seal driver weight
Fork seal driver attachment

This tool is used to install the front fork’s oil
seal and dust seal.

90890-03008

Micrometer

This tool is used to measure the piston skirt
diameter.

90890-03017

Cylinder bore gauge (50~100mm)

This gauge is used to measure cylinder bore.

Vacuum gauge
90890-03094
Valve gauge
attachment
90890-03060

Vacuum gauge
Vacuum gauge attachment

This gauge is used to synchronize the carbu-
retors.

Compression
gauge
90890-03081
Adapter
90890-04136

Compression gauge
Adapter

These tools are used to measure engine
compression.

90890-03112

Pocket tester

This tool is used to check the electrical sys-
tem.

Содержание YZF-R6










































































































































































































































































































































































































































Результаты поиска

Содержание YZF-R6

Отзывы:

Бренды по названию

Популярные бренды

Yamaha YZF-R6, Руководство по обслуживанию

Результаты поиска

Содержание YZF-R6

Отзывы:

Бренды по названию

Популярные бренды