manualshive.com logo in svg

Yamaha YZF-R6, Руководство по обслуживанию

Поделиться
Скачать
Yamaha YZF-R6 Скачать руководство пользователя страница 111

3-42

CHECKING THE BRAKE PADS/

ADJUSTING THE REAR BRAKE LIGHT SWITCH

CHK

ADJ

A

B

NOTE:

a

b

EB304032

CHECKING THE BRAKE PADS
The following procedure applies to all of the
brake pads.
1. Operate the brake.
2. Check:

front brake pad

rear brake pad
Brake pad wear limit 

a

Wear limit reached 

 Replace the brake

pads as a set.
Refer to “FRONT AND REAR BRAKES” in
chapter 7.

Brake pad wear limit

a

 0.5 mm 

b

 0.8 mm

A Front brake

B Rear brake

EB304050

ADJUSTING THE REAR BRAKE LIGHT
SWITCH

The rear brake light switch is operated by
movement of the brake pedal.

The rear brake light switch is properly adjusted
when the brake light comes on just before the
braking effect starts.

1. Check:

rear brake light operation timing
Incorrect 

 Adjust.

2. Adjust:

rear brake light operation timing

a. Hold the main body 

1

 of the rear brake light

switch so that it does not rotate and turn the
adjusting nut 

2

 in direction 

a

 or 

b

 until the

rear brake light comes on at the proper time.

Direction

Brake light comes on
sooner.

Direction

Brake light comes on
later.

Содержание YZF-R6










































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды