Yamaha YZF-R6 Скачать руководство пользователя

Страница: 213 / 425

4-73

CONNECTING RODS AND PISTONS

ENG

NOTE:

CAUTION:

c. Put a piece of Plastigauge



on the crank-

shaft pin.

d. Assemble the connecting rod halves.

Do not move the connecting rod or crankshaft
until the clearance measurement has been
completed.

Lubricate the bolt threads and nut seats with
molybdenum disulfide grease.

Make sure that the “Y” mark

on the connect-

ing rod faces towards the left side of the crank-
shaft.

Make sure that the characters

on both the

connecting rod and connecting rod cap are
aligned.

e. Tighten the connecting rod nuts.

When tightening the connecting rod nuts,
be sure to use an F-type torque wrench.

After tightening the connecting rod nut to
the specified torque, turn the connecting
rod nut 90

Refer to “INSTALLING THE PISTONS AND
CONNECTING RODS”.

Connecting rod nut

15 Nm (1.5 m

kg) + 90

f. Remove the connecting rod and big end

bearings.
Refer to “REMOVING THE CONNECTING
RODS AND PISTONS”.

g. Measure the compressed Plastigauge



width

on the crankshaft pin.

If the crankshaft-pin-to-big-end-bearing
clearance is out of specification, select re-
placement big end bearings.

Содержание YZF-R6










































































































































































































































































































































































































































Результаты поиска

Содержание YZF-R6

Отзывы:

Похожие инструкции для YZF-R6

Бренды по названию

Популярные бренды

Yamaha YZF-R6, Руководство по обслуживанию

Результаты поиска

Содержание YZF-R6

Отзывы:

Похожие инструкции для YZF-R6

Бренды по названию

Популярные бренды