Yamaha YZF-R6 Скачать руководство пользователя страница 119

Страница: 119 / 425

3-50

CHECKING AND ADJUSTING THE STEERING HEAD/

CHECKING THE FRONT FORK

CHK

ADJ

WARNING

d. Hold the spring gauge at a 90

angle from

the handlebar, pull the spring gauge, and re-
cord the measurement when the handlebar
starts to turn.

Steering head tension

200

500 g

e. Repeat the above procedure on the opposite

handlebar.

f. If the steering head tension is out of specifi-

cation (both handlebars should be within
specification), remove the upper bracket and
loosen or tighten the upper ring nut.

g. Reinstall the upper bracket and measure the

steering head tension again as described
above.

h. Repeat the above procedure until the steer-

ing head tension is within specification.

i. Grasp the bottom of the front fork legs and

gently rock the front fork.
Looseness or binding

Adjust the steering

head.

EB304141

CHECKING THE FRONT FORK
1. Stand the motorcycle on a level surface.

Securely support the motorcycle so that
there is no danger of it falling over.

2. Check:

inner tube

Damage / scratches

Replace.

oil seal

Oil leakage

Replace.

3. Hold the motorcycle upright and apply the

front brake.

4. Check:

front fork operation
Push down hard on the handlebars several
times and check if the front fork rebounds
smoothly.
Rough movement

Repair.

Refer to “FRONT FORK” in chapter 7.

Содержание YZF-R6










































































































































































































































































































































































































































Результаты поиска

Содержание YZF-R6

Отзывы:

Бренды по названию

Популярные бренды

Yamaha YZF-R6, Руководство по обслуживанию

Результаты поиска

Содержание YZF-R6

Отзывы:

Бренды по названию

Популярные бренды