Yamaha VZ150 страница 64 Скачать руководство пользователя | Manualshive

Страница: 64 / 92

background image

Maintenance

58

Checkpoints

●

Fuel system parts leakage

●

Fuel line joint leakage

●

Fuel line cracks or other damage

●

Fuel connector leakage

EMU29041

Inspecting idling speed

WARNING

EWM00451

●

Do not touch or remove electrical parts
when starting or during operation.

●

Keep hands, hair, and clothes away
from the flywheel and other rotating

parts while the engine is running.

CAUTION:

ECM00490

This procedure must be performed while
the outboard motor is in the water. A
flushing attachment or test tank can be

used.

A diagnostic tachometer should be used for

this procedure. Results may vary depending
on whether testing is conducted with the
flushing attachment, in a test tank, or with the
outboard motor in the water.
1.

Start the engine and allow it to warm up
fully in neutral until it is running smooth-
ly.

NOTE:

Correct idling speed inspection is only possi-
ble if the engine is fully warmed up. If not
warmed up fully, the idle speed will measure
higher than normal. If you have difficulty ver-
ifying the idle speed, or the idle speed re-
quires adjustment, consult a Yamaha dealer

or other qualified mechanic.

2.

Verify whether the idle speed is set to
specification. For idle speed specifica-
tions, see page 48.

EMU29050

Checking water in engine oil tank

Oil injection models

There is a water trap at the bottom of the en-
gine oil tank. If water or foreign matter is vis-
ible in this trap, consult your Yamaha dealer.

EMU29112

Checking wiring and connectors

●

Check that each grounding wire is properly
secured.

ZMU04004

1. Water trap
2. Engine oil tank

2

1

ZMU01895

«
...
62
63
64
65
66
...
»

Содержание VZ150





























































































Отзывы:

Нет отзывов

Похожие инструкции для VZ150

Бренд: EPOX Страницы: 9

Бренд: Maxtang Страницы: 13

Бренд: AOpen Страницы: 44

Бренд: MSI Страницы: 104

Бренд: Hanasis Страницы: 31

Бренд: TYAN Страницы: 130

Бренд: Gigabyte Страницы: 113

D2550ITX Series

Бренд: Zotac Страницы: 50

Бренд: IEI Technology Страницы: 21

OPTIREG PMIC TLF30682QVS01

Бренд: Infineon Страницы: 24

Бренд: MSI Страницы: 108

Бренд: DFI Страницы: 59

Бренд: DFI Страницы: 115

Бренд: DFI Страницы: 144

Бренд: Gigabyte Страницы: 40

Бренд: Biostar Страницы: 84

Бренд: Asus Страницы: 2

Бренд: Abit Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды