Yamaha VZ150 страница 51 Скачать руководство пользователя | Manualshive

Страница: 51 / 92

background image

Operation

45

few minutes. Otherwise fuel may leak.

CAUTION:

ECM00241

●

Before tilting the outboard motor, stop
the engine by following the procedure
on page 42. Never tilt the outboard mo-
tor while the engine is running. Severe
damage from overheating can result.

●

Do not tilt up the engine by pushing the
tiller handle (if equipped) because this

could break the handle.

EMU28007

Procedure for tilting up (power trim
and tilt models / power tilt models)

1.

Place the remote control lever / gear
shift lever in neutral.

2.

Disconnect the fuel line from the out-
board motor or close the fuel cock.

3.

Press the power trim and tilt switch /
power tilt switch “

” (up) until the out-

board motor has tilted up completely.

4.

Push the tilt support knob into the clamp
bracket or pull the tilt support lever to-
ward you to support the engine.

WARNING

EWM00260

After tilting the outboard motor, be sure
to support it with the tilt support knob or
tilt support lever. Otherwise the outboard
motor could fall back down suddenly if oil
in the power trim and tilt unit loses pres-

N

ZMU03196

UP

ZMU03995

ZMU03996

«
...
49
50
51
52
53
...
»

Содержание VZ150





























































































Отзывы:

Нет отзывов

Похожие инструкции для VZ150

Бренд: E-peas Страницы: 2

Бренд: IBASE Technology Страницы: 93

Бренд: JETWAY Страницы: 48

Бренд: MATSONIC Страницы: 78

Бренд: ASROCK Страницы: 221

Бренд: MediaQ Страницы: 25

Бренд: Icop Страницы: 40

Бренд: Microchip Technology Страницы: 31

126791-HMC764LP6C

Бренд: Analog Devices Страницы: 18

Бренд: Supermicro Страницы: 97

Бренд: Supero Страницы: 89

Бренд: Daewoo Страницы: 46

Бренд: Gigabyte Страницы: 72

Бренд: ECS Страницы: 60

Бренд: Raisonance Страницы: 46

Бренд: Aaeon Страницы: 44

Бренд: Quick Страницы: 30

Бренд: PC Chips Страницы: 49

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды