Yamaha VZ150 страница 41 Скачать руководство пользователя

Страница: 41 / 92

Operation

EMU27221

Operation after a long period of
storage

When operating the engine after a long peri-
od (12 months) of storage, proceed as fol-
lows:
1.

Start the engine. Leave it idling.

WARNING

EWM00090

●

Do not touch or remove electrical parts
when starting or during operation.

●

Keep hands, hair, and clothes away
from the flywheel and other rotating

parts while the engine is running.

Watch for oil flowing through the oil feed
pipes. After any air in the oil lines has
been expelled, the oil injection system
should supply oil normally. If no oil is
flowing after 10 minutes of idling, consult
your Yamaha dealer.

CAUTION:

ECM00560

●

Be sure to take the above steps when
operating the engine after a long period
of storage. Otherwise engine seizure
could occur.

●

Use straight gasoline only. If premix
fuel is used, the fuel injector could be

damaged.

ZMU03988

ZMU03989

Содержание VZ150





























































































Результаты поиска

Содержание VZ150

Отзывы:

Похожие инструкции для VZ150

Бренды по названию

Популярные бренды

Yamaha VZ150, Руководство пользователя

Результаты поиска

Содержание VZ150

Отзывы:

Похожие инструкции для VZ150

Бренды по названию

Популярные бренды