Yamaha VZ150 страница 68 Скачать руководство пользователя | Manualshive

Страница: 68 / 92

background image

Maintenance

62

NOTE:

If the propeller nut does not align with the
propeller shaft hole after tightening to the
specified torque, tighten the nut further to

align it with the hole.

EMU29282

Changing gear oil

WARNING

EWM00800

●

Be sure the outboard motor is securely
fastened to the transom or a stable
stand. You could be severely injured if
the outboard motor falls on you.

●

Never get under the lower unit while it
is tilted, even when the tilt support lever
or knob is locked. Severe injury could
occur if the outboard motor accidental-

ly falls.

1.

Tilt the outboard motor so that the gear
oil drain screw is at the lowest point pos-
sible.

2.

Place a suitable container under the
gear case.

3.

Remove the gear oil drain screw and
gasket.

NOTE:

●

If a magnetic gear oil drain screw is

equipped, remove all metal particles from
the screw before installing it.

●

Always use new gaskets. Do not reuse the

removed gaskets.

4.

Remove the oil level plug and gasket to
allow the oil to drain completely.

CAUTION:

ECM00710

Inspect the used oil after it has been
drained. If the oil is milky, water is getting
into the gear case which can cause gear
damage. Consult a Yamaha dealer for re-

pair of the lower unit seals.

NOTE:

For disposal of used oil, consult your

Yamaha dealer.

5.

With the outboard motor in a vertical po-
sition, and using a flexible or pressur-
ized filling device, inject the gear oil into
the gear oil drain screw hole.

6.

Put a new gasket on the oil level plug.
When the oil begins to flow out of the oil
level plug hole, insert and tighten the oil

1. Gear oil drain screw
2. Oil level plug

1

2

ZMU01899

Recommended gear oil:

Hypoid gear oil SAE#90

Gear oil quantity:

980.0 cm

3

(33.13 US oz) (34.56

Imp.oz)

ZMU01900

«
...
66
67
68
69
70
...
»

Содержание VZ150





























































































Отзывы:

Нет отзывов

Похожие инструкции для VZ150

Бренд: Abit Страницы: 72

Бренд: JETWAY Страницы: 41

Бренд: Linear Technology Страницы: 16

Бренд: Gigabyte Страницы: 104

ISL70219ASEHEV1Z

Бренд: Intersil Страницы: 10

Бренд: MSI Страницы: 171

Бренд: Supero Страницы: 77

Бренд: Supermicro Страницы: 147

Бренд: Supermicro Страницы: 124

Бренд: Broadcom Страницы: 20

Бренд: IDT Страницы: 5

Бренд: SOLTEK Страницы: 94

Бренд: One Control Страницы: 8

Бренд: Gigabyte Страницы: 44

Бренд: Octek Страницы: 84

FIERCE 2 54LB/48

Бренд: Watersnake Страницы: 44

Venom SXW 34/26

Бренд: Watersnake Страницы: 44

ADVANCE SWS 70/36

Бренд: Watersnake Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды