Yamaha VZ150 страница 52 Скачать руководство пользователя | Manualshive

Страница: 52 / 92

background image

Operation

46

sure.

5.

Models equipped with trim rods: Once
the outboard motor is supported with the
tilt support lever, press the power trim
and tilt switch / power tilt switch “

”

(down) to retract the trim rods.

CAUTION:

ECM00250

Be sure to retract the trim rods complete-
ly during mooring. This protects the rods
from marine growth and corrosion which
could damage the power trim and tilt

mechanism.

EMU28055

Procedure for tilting down (power
trim and tilt models / power tilt
models)

1.

Push the power trim and tilt switch / pow-
er tilt switch “

” (up) until the outboard

motor is supported by the tilt rod and the
tilt support lever / tilt support knob be-
comes free.

2.

Release the tilt support lever or pull out
the tilt support knob.

3.

Push the power trim and tilt switch / pow-
er tilt switch “

” (down) to lower the out-

board motor to the desired position.

EMU28060

Cruising in shallow water

The outboard motor can be tilted up partially
to allow operation in shallow water.

EMU28090

Power trim and tilt models / power tilt
models

The outboard motor can be tilted up partially

ZMU03997

ZMU03998

DN

ZMU01936

UP

DN

DN

ZMU03999

«
...
50
51
52
53
54
...
»

Содержание VZ150





























































































Отзывы:

Нет отзывов

Похожие инструкции для VZ150

Бренд: u-blox Страницы: 2

Бренд: IEI Technology Страницы: 126

AP0100CSSL00SPGAH-GEVB

Бренд: ON Semiconductor Страницы: 6

Nucleo STM32F302R8

Бренд: ST Страницы: 18

Бренд: JETWAY Страницы: 48

Бренд: Avalue Technology Страницы: 75

Бренд: Gigabyte Страницы: 87

LCD Programmer Module

Бренд: Xtralis VESDA Страницы: 54

Бренд: ECS Страницы: 92

Бренд: JETWAY Страницы: 52

Бренд: Renesas Страницы: 17

Бренд: Aaeon Страницы: 111

Бренд: Memec Страницы: 45

Бренд: Magic-Pro Computer Страницы: 40

Бренд: Texas Instruments Страницы: 27

Бренд: Intersil Страницы: 6

Бренд: Gigabyte Страницы: 34

P4 Titan GA-8SIMLH-P

Бренд: Gigabyte Страницы: 104

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды