Yamaha VZ150 страница 77 Скачать руководство пользователя | Manualshive

Страница: 77 / 92

background image

Trouble Recovery

71

EMU29522

Power trim and tilt / power tilt will not
operate

If the engine cannot be tilted up or down with
the power trim and tilt / the power tilt because
of a discharged battery or a failure with the
power trim and tilt unit / the power tilt unit, the
engine can be tilted manually.
1.

Loosen the manual valve screw by turn-
ing it counterclockwise until it stops.

2.

Put the engine in the desired position,
then tighten the manual valve screw by
turning it clockwise.

EMU31780

Water separator warning indicator
blinks while cruising

WARNING

EWM01500

Gasoline is highly flammable, and its va-
pors are flammable and explosive.

●

Do not perform this procedure on a hot
or running engine. Allow the engine to
cool.

●

There will be fuel in the fuel filter. Keep
away from sparks, cigarettes, flames or
other sources of ignition.

●

This procedure will allow some fuel to
spill. Catch fuel in a rag. Wipe up any
spilled fuel immediately.

●

The fuel filter must be reassembled
carefully with the O-ring, filter cup, and
hoses in place. Improper assembly or
replacement could result in a fuel leak,
which could result in a fire or explosion

hazard.

If the water separator warning indicator on
the tachometer blinks, perform the following
procedure.

1. Electrical cover
2. Fuse holder
3. Fuse (20A x 3, 30A, 80A x 2)
4. Spare fuse (20A, 30A, 80A)
5. Fuse puller

1. Fuse puller

4

5

2

3

4

3

1

ZMU04009

1

ZMU03562

1. Manual valve screw

ZMU03464

1

«
...
75
76
77
78
79
...
»

Содержание VZ150





























































































Отзывы:

Нет отзывов

Похожие инструкции для VZ150

Бренд: Garelick Страницы: 3

Бренд: Actel Страницы: 2

Бренд: MSI Страницы: 186

Бренд: Texas Instruments Страницы: 21

Бренд: ON Semiconductor Страницы: 8

COMe Ref.Carrier T6

Бренд: Kontron Страницы: 41

Бренд: AOpen Страницы: 8

SIDE POWER SRH 240 TC

Бренд: SLEIPNER MOTOR AS Страницы: 28

Бренд: Texas Instruments Страницы: 28

Бренд: TYAN Страницы: 54

Бренд: TYAN Страницы: 62

Бренд: TYAN Страницы: 54

Бренд: ASROCK Страницы: 40

Бренд: Fujitsu Страницы: 32

Бренд: Fujitsu Страницы: 23

Бренд: Fujitsu Страницы: 40

Бренд: Fujitsu Страницы: 41

Бренд: Fujitsu Страницы: 35

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды