background image

 

General information

 

5

 

EMU25401

 

Label

WARNING

 

EWM01260 

 

 

Be sure shift control is in neutral before
starting engine. (except 2HP)

 

 

Do not touch or remove electrical parts
when starting or during operation.

 

 

Keep hands, hair, and clothes away
from flywheel and other rotating parts

 

while engine is running.

 

EMU25451

 

Label

 

ENGINE OIL ONLY

 

 

Pour the engine oil into this oil tank, not
gasoline.

RECOMMENDED OIL:
YAMALUBE 2 STROKE OUTBOARD OIL or
an equivalent TC-W3 certified ouboard oil.

WARNING

 

EWM01270 

 

Do not add gasoline to the oil tank. Fire

 

explosion could result.

 

EMU30471

 

Label

WARNING

 

EWM01411 

 

Hot surface under this cover during and
after operation. To avoid burns, do not

 

touch finned resistor with bare hands.

 

EMU25465

 

Caution labels

 

EMU30430

 

Label

CAUTION:

 

ECM01440 

 

USE UNLEADED STRAIGHT GASOLINE
ONLY

 

 

Gasoline containing lead can cause
performance loss and engine damage.

 

 

Do not use gasoline mixed with oil (pre-
mix).

 

 

Use YAMALUBE 2-stroke outboard oil
or another 2-stroke engine oil with a
NMMA-certified TC-W3 rate.

 

Refer to Owner’s manual.

 

EMU25500

 

Basic boating rules (Rules of 

the road)

 

Just as there are rules which apply when you
are driving on streets and high ways, there
are waterway rules which apply when you
are driving your boat. These rules are used
internationally, and are also enforced by the
United States Coast Guard and local agen-
cies. You should be aware of these rules,
and follow them whenever you encounter
another vessel on the water.
Several sets of rules prevail according to
geographic location, but are all basically the
same as the International Rules of the Road.

ZMU04435

Содержание VZ150





























































































Отзывы: