Yamaha VZ150 страница 53 Скачать руководство пользователя | Manualshive

Страница: 53 / 92

background image

Operation

47

to allow operation in shallow water.

WARNING

EWM00660

●

Place the gear shift in neutral before
setting up for shallow water cruising.

●

Return the outboard motor to its normal
position as soon as the boat is back in

deeper water.

CAUTION:

ECM00260

Do not tilt the outboard motor up so that
the cooling water inlet on the lower unit is
above the surface of the water when set-
ting up for and cruising in shallow water.
Otherwise severe damage from overheat-

ing can result.

EMU28185

Procedure for power trim and tilt / power
tilt models

1.

Place the remote control lever / gear
shift lever in neutral.

2.

Slightly tilt the outboard motor up to the
desired position using the power trim
and tilt switch / power tilt switch.

3.

To return the outboard motor to the nor-
mal running position, press the power
trim and tilt switch / power tilt switch and
slowly tilt the outboard motor down.

EMU28192

Cruising in other conditions

Cruising in salt water

After operating in salt water, flush the cooling
water passages with fresh water to prevent
them from becoming clogged with salt de-
posits.

NOTE:

For cooling system flushing instructions, see

page 49.

Cruising in turbid water

Yamaha strongly recommends that you use
the optional chromium-plated water pump kit
(not available for some models) if you use
the outboard motor in turbid or muddy water
conditions.

UP

ZMU01935

UP

DN

UP

ZMU04000

«
...
51
52
53
54
55
...
»

Содержание VZ150





























































































Отзывы:

Нет отзывов

Похожие инструкции для VZ150

Бренд: Lantronix Страницы: 8

Бренд: Rabbit Страницы: 144

Бренд: u-blox Страницы: 2

EZ-USB HX2LP CY4605

Бренд: Cypress Страницы: 2

Бренд: MSI Страницы: 76

STEVAL-ISB042V1

Бренд: ST Страницы: 26

Бренд: Texas Instruments Страницы: 15

Бренд: Parker Страницы: 56

Бренд: Safran Страницы: 29

Бренд: Gigabyte Страницы: 112

Бренд: EVGA Страницы: 128

Бренд: Intel Страницы: 10

Бренд: SMSC Страницы: 42

Бренд: Silicon Laboratories Страницы: 12

Бренд: Ublox Страницы: 20

Бренд: Draper Страницы: 49

Бренд: Texas Instruments Страницы: 18

K8M800 INFINITY

Бренд: DFI Страницы: 122

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды