Yamaha VX200D Скачать руководство пользователя | Manualshive

Страница: 23 / 81

background image

Basic components

18

EMU26550

Oil level indicator (digital type)

This indicator shows the engine oil level. If
the oil level falls below the lower limit, the
warning indicator will start to blink. For fur-
ther information, see page 22.

CAUTION:

ECM00030

Do not operate the engine without oil. Se-

rious engine damage will occur.

EMU26581

Overheat warning indicator (digital
type)

If the engine temperature rises too high, the
warning indicator will start to blink. For fur-
ther information on reading the indicator, see

page 21.

CAUTION:

ECM00050

Do not continue to run the engine if the
overheat warning indicator is on. Serious

engine damage will occur.

EMU26600

Speedometer (digital type)

This gauge shows the boat speed.

NOTE:

After the main switch is first turned on, all
segments of the display come on as a test.
After a few seconds, the gauge will change
to normal operation. Watch the gauge when

1. Oil level indicators

1. Oil level indicator

ZMU04580

1

1

ZMU01867

1. Overheat warning indicator

1. Speedometer
2. Fuel gauge
3. Trip meter/clock/voltmeter
4. Warning indicator(s)

1

ZMU01868

✩✩✬✤✫✲✣ ✤✫

«
...
21
22
23
24
25
...
»

Содержание VX200D


















































































Отзывы:

Нет отзывов

Похожие инструкции для VX200D

Бренд: Aaeon Страницы: 132

Бренд: Aaeon Страницы: 50

Бренд: Intel Страницы: 80

EZ-USB HX2LP CY4605

Бренд: Cypress Страницы: 2

Бренд: DFI Страницы: 104

Бренд: DFI Страницы: 60

Бренд: Linear Technology Страницы: 7

Бренд: SmartOne Страницы: 2

Бренд: AOpen Страницы: 8

Бренд: TYAN Страницы: 47

Бренд: C&T Solution Страницы: 48

FRDMDUALK3664EVB

Бренд: NXP Semiconductors Страницы: 17

Бренд: Acrosser Technology Страницы: 3

GA-N650SLI-DS4L

Бренд: Gigabyte Страницы: 100

Бренд: ON Semiconductor Страницы: 5

Бренд: Ublox Страницы: 2

Бренд: IDT Страницы: 5

Бренд: NXP Semiconductors Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды