Yamaha VX200D Скачать руководство пользователя | Manualshive

Страница: 56 / 81

background image

Maintenance

51

gine oil tank. If water or foreign matter is vis-
ible in this trap, consult your Yamaha dealer.

EMU29111

Checking wiring and connectors

●

Check that each grounding wire is properly
secured.

●

Check that each connector is engaged se-
curely.

EMU29120

Exhaust leakage

Start the engine and check that no exhaust
leaks from the joints between the exhaust
cover, cylinder head, and body cylinder.

EMU29130

Water leakage

Start the engine and check that no water
leaks from the joints between the exhaust
cover, cylinder head, and body cylinder.

EMU29153

Checking power trim and tilt system

WARNING

EWM00430

●

Never get under the lower unit while it
is tilted, even when the tilt support lever
is locked. Severe injury could occur if
the outboard motor accidentally falls.

●

Make sure no one is under the outboard

motor before performing this test.

1.

Check the power trim and tilt unit for any
sign of oil leaks.

2.

Operate each of the power trim and tilt
switches on the remote control and en-
gine bottom cowling (if equipped) to
check that all switches work.

3.

Tilt the outboard motor up and check
that the tilt rod and trim rods are extend-
ed completely.

4.

Use the tilt support lever to lock the mo-
tor in the up position. Operate the tilt
down switch briefly so the motor is sup-
ported by the tilt support lever.

1. Water trap
2. Engine oil tank

2

1

ZMU01895

ZMU03915

1. Tilt rod
2. Trim rods

2

1

ZMU03531

✩✩✬✤✫✲✣ ✤

«
...
54
55
56
57
58
...
»

Содержание VX200D


















































































Отзывы:

Нет отзывов

Похожие инструкции для VX200D

Бренд: Hailo Страницы: 22

Бренд: Abit Страницы: 72

Бренд: RAK Страницы: 17

EmbCore ROM-7421

Бренд: Advantech Страницы: 25

Бренд: Gigabyte Страницы: 116

Бренд: Unicorn Computer Страницы: 36

Бренд: Texas Instruments Страницы: 6

K8T8AS - REV 3.0

Бренд: JETWAY Страницы: 26

Бренд: JETWAY Страницы: 48

Бренд: ASROCK Страницы: 160

i.MX 8M Mini SODIMM SOM

Бренд: iWave Страницы: 16

Бренд: Texas Instruments Страницы: 20

Бренд: Supermicro Страницы: 1

Бренд: JETWAY Страницы: 51

Бренд: Gigabyte Страницы: 96

Бренд: MSI Страницы: 118

Бренд: Atmel Страницы: 74

Бренд: Foxconn Страницы: 106

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды