manualshive.com logo in svg

Yamaha VX200D, Руководство пользователя

Поделиться
Скачать
Yamaha VX200D Скачать руководство пользователя страница 46

 

Maintenance

 

41

 

and Stabilizer” (Part No. LUB-FUELC-
12-00) to each gallon of fuel.

NOTE:

 

The use of “Yamaha Fuel Conditioner and
Stabilizer” eliminates the need to drain the
fuel system. Consult your Yamaha dealer or
other qualified mechanic if the fuel system is

 

to be drained instead.

3.

Remove the top cowling and silencer
cover/cap. Remove the propeller.

4.

Install the flushing attachment over the
cooling water inlet.

CAUTION:

 

ECM00300 

 

Do not run the engine without supplying
it with cooling water. Either the engine
water pump will be damaged or the en-
gine will be damaged from overheating.
Before starting the engine, be sure to
supply water to the cooling water passag-

 

es.

CAUTION:

 

ECM00310 

 

Avoid running the outboard motor at high
speed while on the flushing attachment,

 

otherwise overheating could occur.

 

5.

Cooling system flushing is essential to
prevent the cooling system from clog-

ging up with salt, sand, or dirt. In addi-
tion, fogging/lubricating of the engine is
mandatory to prevent excessive engine
damage due to rust. Perform the flush-
ing and fogging at the same time.

WARNING

 

EWM00090 

 

●

 

Do not touch or remove electrical parts
when starting or during operation.

 

●

 

Keep hands, hair, and clothes away
from the flywheel and other rotating

 

parts while the engine is running.

 

6.

Run the engine at a fast idle for 10–15
minutes in neutral position while supply-
ing fresh water.

7.

Just prior to turning off the engine, quick-
ly spray “Yamaha Stor-Rite Engine
Fogging Oil” (Part No. LUB-STRRT-12-
00) alternately into each carburetor/
each intake manifold. When properly
done, the engine will smoke excessively
and almost stall.

8.

Remove the flushing attachment and
wipe off any excess water.

9.

Install the silencer cover/cap and top
cowling. Install the propeller.

NOTE:

 

A flushing attachment is available from your

 

Yamaha dealer.

 

EMU28410

 

Lubrication (oil injection models)

 

1.

Grease the spark plug threads and in-
stall the spark plug(s) and torque to
proper specification. For information on
spark plug installation, see page 47.

2.

Fill the oil tanks. This prevents the for-
mation of condensation. For models with
a remote oil tank, it may be necessary to
manually override the control unit to
completely fill the engine oil tank.

 

1. Flushing attachment

✩✩✬✤✫✲✣ ✧✤   

Содержание VX200D


















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды