Yamaha VX200D Скачать руководство пользователя | Manualshive

Страница: 35 / 81

background image

Operation

30

EMU27450

Operating engine

EMU27480

Feeding fuel

WARNING

EWM00420

●

Before starting the engine, make sure
that the boat is tightly moored and that
you can steer clear of any obstructions.
Be sure there are no swimmers in the
water near you.

●

When the air vent screw is loosened,
gasoline vapor will be released. Gaso-
line is highly flammable, and its vapors
are flammable and explosive. Refrain
from smoking, and keep away from
open flames and sparks while loosen-
ing the air vent screw.

●

This product emits exhaust gases
which contain carbon monoxide, a col-
orless, odorless gas which could cause
brain damage or death when inhaled.
Symptoms include nausea, dizziness,
and drowsiness. Keep cockpit and cab-
in areas well ventilated. Avoid blocking

exhaust outlets.

1.

If there is an air vent screw on the fuel
tank cap, loosen it 2 or 3 turns.

2.

If there is a fuel joint or a fuel cock on the
boat, firmly connect the fuel line to the
joint or open the fuel cock.

3.

Squeeze the primer pump with the outlet
end up until you feel it become firm.

EMU27490

Starting engine

EMU27662

Electric start and remote control models

1.

Place the remote control lever in neutral.

NOTE:

The start-in-gear protection device prevents
the engine from starting except when in neu-

tral.

2.

Attach the engine stop switch lanyard to
a secure place on your clothing, or your
arm or leg. Then install the lock plate on
the other end of the lanyard into the en-
gine stop switch.

WARNING

EWM00120

●

Attach the engine stop switch lanyard
to a secure place on your clothing, or
your arm or leg while operating.

●

Do not attach the lanyard to clothing
that could tear loose. Do not route the

✩✩✬✤✫✲✣ ✦✣

«
...
33
34
35
36
37
...
»

Содержание VX200D


















































































Отзывы:

Нет отзывов

Похожие инструкции для VX200D

Бренд: ON Semiconductor Страницы: 17

Бренд: EPOX Страницы: 9

Бренд: J&W Страницы: 40

Advance 10T Series

Бренд: QDI Страницы: 74

Бренд: EVGA Страницы: 2

Бренд: ASROCK Страницы: 200

Бренд: Lite-on Tech Страницы: 49

Бренд: ASROCK Страницы: 2

Бренд: RIB Страницы: 12

Бренд: Javad Страницы: 12

Бренд: Abit Страницы: 110

Бренд: Seanix Страницы: 54

Бренд: Norco Страницы: 55

Бренд: ON Semiconductor Страницы: 2

Бренд: DFI Страницы: 105

Бренд: DFI Страницы: 123

Бренд: ASROCK Страницы: 41

Бренд: ADLINK Technology Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды