manualshive.com logo in svg

Yamaha VX200D, Руководство пользователя

Поделиться
Скачать
Yamaha VX200D Скачать руководство пользователя страница 57

 

Maintenance

 

52

 

5.

Check that the tilt rod and trim rods are
free of corrosion or other flaws.

6.

Activate the tilt-down switch until the trim
rods have retracted completely into the
cylinders.

7.

Activate the trim-up switch until the tilt
rod is fully extended. Unlock the tilt sup-
port lever.

8.

Tilt the outboard motor down. Check

that the tilt rod and trim rods operate
smoothly.

NOTE:

 

Consult your Yamaha dealer if any operation

 

is abnormal.

 

EMU29171

 

Checking propeller

WARNING

 

EWM00321 

 

You could be seriously injured if the en-
gine accidentally starts when you are
near the propeller.

 

●

 

Before inspecting, removing, or install-
ing the propeller, remove the spark
plug caps from the spark plugs. Also,
place the shift control in neutral, turn
the main switch to “

” (off) and re-

move the key, and remove the lanyard
from the engine stop switch. Turn off
the battery cut-off switch if your boat
has one.

 

●

 

Do not use your hand to hold the pro-
peller when loosening or tightening the
propeller nut. Put a wood block be-
tween the anti-cavitation plate and the
propeller to prevent the propeller from

 

turning.

 

1. Tilt support lever

ZMU03533

1

ZMU05037

ZMU03532

ZMU01896

✩✩✬✤✫✲✣ ✥   

Содержание VX200D


















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды