Yamaha VX200D Скачать руководство пользователя | Manualshive

Страница: 71 / 81

background image

Trouble Recovery

66

4.

After using the emergency switch, turn
off the main switch, then turn it back on.
This resets the warning system to nor-
mal operation. The yellow segment will
continue to be displayed on the oil level
indicator.

5.

Start the engine and return to the near-
est port for more oil.

NOTE:

●

The maximum reserve oil capacity is 1500
cm

3

(1.6 US qt, 1.31 Imp qt).

●

The oil-feed pump will not operate if the
engine is tilted up more than 35°. Put the
engine in the upright position (not tilted)

before using the emergency switch.

EMU29750

Top cowling does not unlock

If the top cowling stays locked when the re-
lease lever is operated, the cable may be
damaged or incorrectly adjusted.
1.

Pull the cowling release lever to unlock
the front lock.

2.

Pull the emergency cowling release wire
coming out of the hole on the side of the
pilot hole in the bottom cowling to re-
lease the port side rear lock.

3.

Lift the port side of the top cowling to pull
out the emergency cowling release wire
from the port side of the bottom cowling.

4.

Pull the emergency cowling release wire
to release the starboard side rear lock.

CAUTION:

ECM00390

Be sure the problem with the cowling lock
is repaired before reinstalling the cowl-

ing.

EMU29760

Treatment of submerged motor

If the outboard motor is submerged, immedi-
ately take it to a Yamaha dealer. Otherwise
some corrosion may begin almost immedi-
ately.

1. Emergency switch

1. Engine oil tank
2. Remote oil tank

1

ZMU04168

1

2

ZMU01908

1. Cowling release lever
2. Starboard-side cowling release wire
3. Port-side cowling release wire

1

2

3

ZMU03544

✩✩✬✤✫✲✣ ✩✩

«
...
69
70
71
72
73
...
»

Содержание VX200D


















































































Отзывы:

Нет отзывов

Похожие инструкции для VX200D

Бренд: Intel Страницы: 76

Бренд: MSI Страницы: 36

Бренд: NXP Semiconductors Страницы: 28

Бренд: NXP Semiconductors Страницы: 16

Бренд: Microsemi Страницы: 15

Бренд: Tews Technologies Страницы: 26

C5535 DSPShield

Бренд: Texas Instruments Страницы: 49

Cypress MB39C502-EVBSK-01

Бренд: Infineon Technologies Страницы: 28

Бренд: Biostar Страницы: 166

K8T8AS - REV 3.0

Бренд: JETWAY Страницы: 26

Бренд: Texas Instruments Страницы: 20

Бренд: ASROCK Страницы: 106

Бренд: Supermicro Страницы: 107

Supero C9X299-PG300F

Бренд: Supermicro Страницы: 28

Бренд: MSI Страницы: 148

Бренд: Sleipner Страницы: 24

LanParty UT NF4 SLI EXPERT Venus

Бренд: DFI Страницы: 161

Бренд: ASROCK Страницы: 260

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды