manualshive.com logo in svg

Yamaha VX200D, Руководство пользователя

Поделиться
Скачать
Yamaha VX200D Скачать руководство пользователя страница 70

 

Trouble Recovery

 

65

NOTE:

 

When the engine does not start with this pro-

 

cedure, see page 65.

 

EMU29670

 

Engine fails to operate

 

EMU29691

 

Ignition system malfunction

 

If the battery voltage is low or in the unlikely
event of an ignition system malfunction, the
engine speed may become erratic or the en-
gine may stop. In such a situation, follow the
procedure below.
1.

Remove the CDI unit cover or electrical
cover, if equipped.

2.

Disconnect the yellow cord (emergency
circuit) of the CDI unit to return to port.

WARNING

 

EWM00350 

 

When the yellow cord is disconnected,
the idle and low speeds are slightly high-
er than normal. Use care when starting off

 

or stopping.

CAUTION:

 

ECM00380 

 

Follow this procedure only in an emer-
gency and just long enough to return to

 

port for repairs.

 

EMU29741

 

Low oil level warning activates

 

If the oil level is allowed to drop too low, the
red segment will appear on the oil level indi-
cator, the buzzer will sound, and engine
speed will be limited to about 2000 r/min. If
this happens, a reserve amount of oil can be
pumped from the remote oil tank to the en-
gine oil tank using the emergency switch.

WARNING

 

EWM01050 

 

Be sure to stop the engine before per-

 

forming this procedure.

CAUTION:

 

ECM00900 

 

●

 

If the emergency switch is held up too
long, too much oil will be pumped into
the engine oil tank, overflowing it. Re-
lease the switch when oil reaches the
upper level line on the engine oil tank.

 

●

 

Do not use this emergency procedure
unless the oil level warning indicators

 

are working.

 

1.

Remove the top cowling.

2.

Turn on the main switch.

3.

Lift the emergency switch to pump re-
serve oil into the engine oil tank from the
remote oil tank.

 

1. CDI unit
2. Emergency connector

1

2

ZMU04213

ON START

OFF

ZMU01906

✩✩✬✤✫✲✣ ✩   

Содержание VX200D


















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды