Yamaha VX200D Скачать руководство пользователя

Страница: 72 / 81

Trouble Recovery

If you cannot immediately take the outboard
motor to a Yamaha dealer, follow the proce-
dure below in order to minimize engine dam-
age.

EMU29790

Procedure

Thoroughly wash away mud, salt, sea-
weed, and so on, with fresh water.

Remove the spark plugs and face the
spark plug holes downward to allow any
water, mud, or contaminants to drain.

Drain the fuel from the vapor separator,
fuel filter, and fuel line.

Feed fogging oil or engine oil through
the intake manifold and spark plug holes
while cranking with the emergency start-
er rope.

Take the outboard motor to a Yamaha
dealer as soon as possible.

CAUTION:

ECM00400

Do not attempt to run the outboard motor

until it has been completely inspected.

ZMU01909

ZMU01910

ZMU01911

✩✩✬✤✫✲✣ ✩✪

Содержание VX200D


















































































Результаты поиска

Содержание VX200D

Отзывы:

Похожие инструкции для VX200D

Бренды по названию

Популярные бренды

Yamaha VX200D, Руководство пользователя

Результаты поиска

Содержание VX200D

Отзывы:

Похожие инструкции для VX200D

Бренды по названию

Популярные бренды