Yamaha RS90GTL Скачать руководство пользователя | Manualshive

Страница: 97 / 104

background image

10-2

CAUTION:

@

●

Always keep the battery charged.
Storing a discharged battery can
cause permanent battery damage.

●

To charge a sealed-type (MF) battery,
a special (constant-voltage) battery
charger is required. Using a conven-
tional battery charger will damage
the battery. If you do not have
access to a sealed-type (MF) battery
charger, have a Yamaha dealer
charge your battery.

●

Do not charge the battery quickly.
Charge the battery for 10 hours at
1.8 amperes.

@

7. Drive track

Loosen the drive track and block up the
chassis so that the track is suspended
above the ground.

8. V-belt

Remove the V-belt and store separately.

9. Storage

Store the snowmobile in a dry, well-venti-
lated place out of direct sunlight. Put a fab-
ric cover over the snowmobile, preferably
one that is designed for it. Do not use a
plastic or vinyl cover—condensation could
be trapped underneath which could
increase the chances of rusting.

Returning to service after storage

When returning your snowmobile to ser-
vice, install the V-belt and battery and
adjust the drive track.
Remove the spark plugs and clean or
replace them if necessary. Perform all
other pre-operation and seasonal mainte-
nance checks listed in the periodic mainte-
nance chart.

NOTE:

@

Before installing the battery, have a
Yamaha dealer inspect and fully charge it.

@

For peak performance, it is recommended
that you have your snowmobile checked
and tuned by a Yamaha dealer. The dealer
has the experience and training to help you
get the maximum performance and use out
of your Yamaha snowmobile.

U8GG10.book Page 2 Thursday, April 28, 2005 5:43 PM

«
...
95
96
97
98
99
...
»

Содержание RS90GTL









































































































Отзывы:

Нет отзывов

Похожие инструкции для RS90GTL

Бренд: ODES Страницы: 92

Бренд: McElroy Страницы: 63

Бренд: Honda Страницы: 513

Бренд: LAMAX Страницы: 150

Бренд: Har-Tru Страницы: 12

Sportsman 9921837

Бренд: Polaris Страницы: 133

Бренд: Eagle Страницы: 29

Бренд: Landoll Страницы: 36

Бренд: Yamaha Страницы: 150

GRIZZLY YFM70GPAL

Бренд: Yamaha Страницы: 182

Бренд: Yamaha Страницы: 108

Бренд: Taxa Outdoors Страницы: 2

Бренд: Ifor Williams Trailers Страницы: 42

Бренд: Range Road Страницы: 6

Black-Topper BT-1 Distributors 2008

Бренд: Etnyre Страницы: 48

Black-Topper CENTENNIAL

Бренд: Etnyre Страницы: 53

Бренд: WilTec Страницы: 7

Бренд: Textron Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды