Yamaha RS90GTL Скачать руководство пользователя

Страница: 81 / 104

8-27

ESU04092

Adjusting the control rods

The weight transfer can be adjusted by turning the con-
trol rod adjuster or adjusting nut.

For RS90R/RS90GT/RSG90

1. Loosen the locknut

2. Turn the control rod adjuster

in direction

increase weight transfer or direction

to decrease

weight transfer.

CD-27E

3. Check the adjuster length

using the scale on the

special wrench

included in the owner’s tool kit as

shown. Make sure that the rim

of the control rod

body is within the range

of the scale.

4. Tighten the locknut while holding the adjuster in

place.

CAUTION:

When using the special wrench, make sure that it is
situated at a right angle to the control rod, and that it
is tightly fitted to the locknut or the control rod
adjuster.

WARNING

Never adjust the control rod beyond the range of the
scale on the special wrench.

Adjuster turning
direction

←

→

Weight transfer

Increased

←

→

Decreased

Locknut tightening torque:

35 Nm (3.5 m·kgf, 25 ft·lb)

U8GG10.book Page 27 Thursday, April 28, 2005 5:43 PM

Содержание RS90GTL









































































































Результаты поиска

Содержание RS90GTL

Отзывы:

Похожие инструкции для RS90GTL

Бренды по названию

Популярные бренды

Yamaha RS90GTL, Руководство пользователя

Результаты поиска

Содержание RS90GTL

Отзывы:

Похожие инструкции для RS90GTL

Бренды по названию

Популярные бренды