Yamaha RS90GTL Скачать руководство пользователя

Страница: 70 / 104

8-16

8. Install the V-belt over the primary sheave assembly.

9. Rotate the secondary sliding sheave clockwise

and push

it so that it separates from the secondary

fixed sheave.

10. Install the V-belt

between the secondary sliding

and secondary fixed sheaves.

11. Install the drive guard.

WARNING

Never run the engine with the V-belt or drive guard
removed.

ESU03513

Checking the drive chain housing oil level and
the drive chain tension

Checking the oil level

WARNING

The engine, oil tank, brake disc, and coolant hoses
will be very hot after the engine has been run. Avoid
contact while they are still hot with any part of your
body or clothing during inspection or repair.

1. Place the snowmobile on a level surface.
2. Remove the dipstick

, wipe it off with a clean rag,

and then insert it back into the filler hole.

U8GG10.book Page 16 Thursday, April 28, 2005 5:43 PM

Содержание RS90GTL









































































































Результаты поиска

Содержание RS90GTL

Отзывы:

Похожие инструкции для RS90GTL

Бренды по названию

Популярные бренды

Yamaha RS90GTL, Руководство пользователя

Результаты поиска

Содержание RS90GTL

Отзывы:

Похожие инструкции для RS90GTL

Бренды по названию

Популярные бренды