Yamaha RS90GTL Скачать руководство пользователя | Manualshive

Страница: 37 / 104

background image

6-5

ESU00087

Throttle lever

Check the throttle lever operation before starting the
engine.
The throttle lever must open smoothly and spring back to
its home position when released.

ESU00090

Throttle override system (T.O.R.S.)

Check the T.O.R.S. for proper operation.

WARNING

@

When checking T.O.R.S.:

●

Make sure that the parking brake is applied.

●

Make sure that the throttle lever moves smoothly.

●

Do not run the engine up to clutch engagement
r/min. Otherwise, the snowmobile could start
moving forward unexpectedly, which could cause
an accident.

@

1. Start the engine.

NOTE:

@

Refer to the “Starting the engine” section.

@

2. Hold the pivot point of the throttle lever away from the

throttle switch by putting your thumb (above) and
forefinger (below) between the throttle lever pivot

1

and the engine stop switch housing

2

.

While holding the pivot point as described above,
press the throttle lever

3

gradually.

The T.O.R.S. will operate and the engine should run
between 2,800 and 3,000 r/min.

WARNING

@

If the engine does not run between 2,800 and
3,000 r/min, stop the engine by turning the main switch
to the “OFF” position and consult a Yamaha dealer.

@

U8GG10.book Page 5 Thursday, April 28, 2005 5:43 PM

«
...
35
36
37
38
39
...
»

Содержание RS90GTL









































































































Отзывы:

Нет отзывов

Похожие инструкции для RS90GTL

Бренд: IceCar Страницы: 37

DS Gold Standard

Бренд: Club Car Страницы: 64

DS Electric 1984

Бренд: Club Car Страницы: 24

Tugger train Autarkic E Frame

Бренд: Still Страницы: 144

Бренд: Texas Страницы: 7

Бренд: HYOSUNG Страницы: 133

Powermover PM5900

Бренд: Ultra-Fab Страницы: 18

Бренд: Leggero Страницы: 63

Бренд: Hammerhead Страницы: 70

Бренд: Hammerhead Off-Road Страницы: 75

Бренд: Yamaha Страницы: 193

Бренд: Jeep Страницы: 20

Бренд: Pongratz Страницы: 11

BANSHEE YFZ350S

Бренд: Yamaha Страницы: 172

1998 Grizzly YFM600FWAK(C)

Бренд: Yamaha Страницы: 159

2012 Grizzly 300

Бренд: Yamaha Страницы: 306

Бренд: KAYO MOTO Страницы: 8

Бренд: TGB Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды