Yamaha RS90GTL Скачать руководство пользователя

Страница: 75 / 104

8-21

CAUTION:

The left and right ski spring preload must be set to
the same setting. Uneven settings can cause poor
handling and loss of stability.

WARNING

This shock absorber contains highly pressurized
nitrogen gas. It could explode by improper handling,
causing injury or property damage.

●

Do not tamper with or attempt to open the shock
absorber.

●

Do not subject the shock absorber to an open
flame or other high heat source, which could
cause it to explode.

●

Do not deform or damage the shock absorber in
any way.

●

Do not dispose of a worn or damaged shock
absorber by yourself. Take the unit to a Yamaha
dealer.

ESU04750

Adjusting the ski damping forces
For RS90GT
Compression damping force

The compression damping force of each ski shock
absorber can be adjusted by turning the compression
damping force adjusting knob

CD-28E

Adjusting knob
position

Turns out

∗

Turns in

Damping

Soft

Hard

∗

With the adjuster fully turned in direction

14 clicks

out

Minimum

Standard

8 clicks

out

Maximum

2 clicks

U8GG10.book Page 21 Thursday, April 28, 2005 5:43 PM

Содержание RS90GTL









































































































Результаты поиска

Содержание RS90GTL

Отзывы:

Похожие инструкции для RS90GTL

Бренды по названию

Популярные бренды

Yamaha RS90GTL, Руководство пользователя

Результаты поиска

Содержание RS90GTL

Отзывы:

Похожие инструкции для RS90GTL

Бренды по названию

Популярные бренды