Yamaha RS90GTL Скачать руководство пользователя

Страница: 33 / 104

6-1

ESU00072

PRE-OPERATION CHECKS

NOTE:

Pre-operation checks should be made each time the
snowmobile is used.

WARNING

The engine and muffler will be very hot after the
engine has been run.
Avoid touching the engine and muffler while they are
still hot with any part of your body or clothing during
inspection or repair.

ESU00075

Fuel

Make sure that there is sufficient fuel in the fuel tank.

WARNING

●

Fuel is HIGHLY FLAMMABLE and poisonous.
Check the “SAFETY INFORMATION” section
carefully before refueling. (See page 3-2.)

●

Do not fill the fuel tank above the bottom of the
filler tube

. Fuel could overflow if the snowmo-

bile is tilted on its side or if the ambient tempera-
ture rises, causing the fuel to warm up and
expand.

●

Make sure that the fuel tank cap is closed
securely after refueling. Leaking fuel can catch
fire.

Fuel level

Recommended fuel:

Unleaded gasoline

Pump octane

; 88 or higher

Fuel tank capacity:

39.3 L (8.6 Imp gal, 10.4 US gal)

R+M

U8GG10.book Page 1 Thursday, April 28, 2005 5:43 PM

Содержание RS90GTL









































































































Результаты поиска

Содержание RS90GTL

Отзывы:

Похожие инструкции для RS90GTL

Бренды по названию

Популярные бренды

Yamaha RS90GTL, Руководство пользователя

Результаты поиска

Содержание RS90GTL

Отзывы:

Похожие инструкции для RS90GTL

Бренды по названию

Популярные бренды