background image

8-30

Adjusting the drive track

WARNING

Be sure to have a Yamaha dealer make this
adjustment. 

Support the snowmobile securely on a suitable
stand before working underneath the snowmo-
bile. 

Operate the engine in a well-ventilated area. 

@

1. Lift the rear of the snowmobile onto a suitable stand

to raise the drive track off the ground. 

2. Loosen the rear axle nut 

1

.

3. Start the engine and rotate the drive track one or two

turns. Stop the engine.

4. Check the drive track alignment with the slide runners

2

. If the alignment is incorrect, align the drive track

by turning the left and right adjusters.

CD-08E

7

Slide runners 

8

Drive track 

9

Slide metal 

a

Gap 

b

Forward

5. Adjust the drive track deflection to specification.

CD-09E

5

6

Drive track 

alignment

5

 Shifted to right

6

 Shifted to left

3

 Left adjuster

Turn out

Turn in

4

 Right adjuster

Turn in

Turn out

Drive track 

deflection

More than 

specified

Less than 

specified

3

 Left adjuster

Turn in

Turn out

4

 Right adjuster

Turn in

Turn out

U8GG10.book  Page 30  Thursday, April 28, 2005  5:43 PM

Содержание RS90GTL









































































































Отзывы: