Yamaha RS90GTL Скачать руководство пользователя страница 52

Страница: 52 / 104

7-9

ESU00347

Driving

WARNING

Be sure to read the “SAFETY INFORMATION” and
“Riding your snowmobile” sections carefully before
operating the snowmobile.

NOTE:

Make sure that the engine is warmed up enough before
riding.

For RS90N/RS90M

1. Release the parking brake by moving the parking

brake lever to the right.

2. Press the throttle lever slowly to move the snowmo-

bile.

3. Turn the handlebar in the desired direction.
4. Squeeze the brake lever to stop the snowmobile.
5. Apply the parking brake by moving the parking brake

lever to the left.

For RS90R/RS90NR/RS90GT/RSG90

1. To select the desired operating position, pull the shift

lever out, slide it to “FWD” or to “REV” until it stops,
and then release it.

Pull out

Slide to “FWD” (Forward)

Slide to “REV” (Reverse)

Release

WARNING

●

Make sure that the throttle lever is fully released
and the snowmobile is at a full stop before shift-
ing.

●

Be sure to slide the shift lever to “FWD” or “REV”
until it stops completely and only while the
engine is idling.

●

Make sure that the area behind the snowmobile is
clear before reversing. Watch behind.

●

Reduce speed and avoid sharp turning when
operating the snowmobile in reverse.

U8GG10.book Page 9 Thursday, April 28, 2005 5:43 PM

Содержание RS90GTL









































































































Результаты поиска

Содержание RS90GTL

Отзывы:

Бренды по названию

Популярные бренды

Yamaha RS90GTL, Руководство пользователя

Результаты поиска

Содержание RS90GTL

Отзывы:

Бренды по названию

Популярные бренды