Yamaha RS90GTL Скачать руководство пользователя

Страница: 76 / 104

8-22

Rebound damping force

The rebound damping force of each ski shock absorber
can be adjusted by turning the rebound damping force
adjusting knob

CD-29E

NOTE:

The damping forces will not decrease past the minimum
levels even if the adjusting knobs are turned out more
than the minimum settings.

CAUTION:

The damping forces for the left and right ski shock
absorbers must be adjusted to the same settings.
Uneven settings can cause poor handling and loss
of stability.

WARNING

This shock absorber contains highly pressurized
nitrogen gas. It could explode by improper handling,
causing injury, or property damage.

●

Do not tamper with or attempt to open the shock
absorber.

●

Do not subject the shock absorber to an open
flame or other high heat source, which could
cause it to explode.

●

Do not deform or damage the shock absorber in
any way.

●

Do not dispose of a worn or damaged shock
absorber by yourself. Take the unit to a Yamaha
dealer.

Adjusting knob
position

Turns out

∗

Turns in

Damping

Soft

Hard

∗

With the adjuster fully turned in direction

20 clicks

out

Minimum

Standard

10 clicks

out

3 clicks

Maximum

U8GG10.book Page 22 Thursday, April 28, 2005 5:43 PM

Содержание RS90GTL









































































































Результаты поиска

Содержание RS90GTL

Отзывы:

Похожие инструкции для RS90GTL

Бренды по названию

Популярные бренды

Yamaha RS90GTL, Руководство пользователя

Результаты поиска

Содержание RS90GTL

Отзывы:

Похожие инструкции для RS90GTL

Бренды по названию

Популярные бренды