manualshive.com logo in svg

Yamaha QL5, Справочное руководство

Yamaha QL5 - мощная цифровая смесительная консоль для профессионалов. Получите свой бесплатный руководство по эксплуатации скачать с manualshive.com. Идеальный выбор для шоу и концертов, с широким набором функций и превосходным качеством звука. Не упустите возможность ознакомиться с полным руководством перед использованием.

Поделиться
Скачать
background image

MIDI

 Reference Manual

162

MIDI/GPI screen (MIDI SETUP page)

You can select the type of MIDI messages that will be transmitted and received, and choose 
the port that will be used.

1

PORT/CH field

Enables you to select the port and MIDI channel that will be used to transmit and receive 
MIDI messages.

•

Tx PORT/Tx CH

......... Press these buttons to open windows in which you can 

respectively select a port and MIDI channel to transmit MIDI 
messages.

•

Rx PORT/Rx CH

........  Press these buttons to open windows in which you can 

respectively select a port and MIDI channel to receive MIDI 
messages.

NOTE

When transmitting or receiving Parameter Changes, the channel number you specify here is used 
as the device number (a number that identifies the transmitting or receiving unit).

2

PROGRAM CHANGE field

Enables you to switch MIDI Program Change message transmission and reception on or 
off.

•

Tx

............................... Switches program change transmission on/off.

•

Rx

............................... Switches program change reception on/off.

•

ECHO

......................... Switches on or off echo output of Program Change messages. 

(If this function is on, Program Change messages received 
from an external device will be retransmitted without 
modification.)

3

PROGRAM CHANGE MODE field

Enables you to select the Program Change transmit/receive mode.

•

SINGLE

...................... If this button is on, Program Changes will be transmitted and 

received on a single MIDI channel (Single mode).

•

MULTI

........................ If this button is on, program changes will be transmitted/

received on multiple MIDI channels (Multi mode).

•

OMNI

.......................... If this button is on, Program Changes on all MIDI channels will 

be received in Single mode. Multi mode transmission/reception 
and Single mode transmission are disabled.

•

BANK

......................... If this button is on, Bank Select messages can be transmitted 

and received in Single mode. (Bank Select messages switch 
the group of Program Change messages to be used.)

4

CONTROL CHANGE field

Enables you to switch MIDI Control Change message transmission and reception on or 
off.

•

Tx

............................... Switches control change transmission on/off.

•

Rx

.............................. Switches control change reception on/off.

•

ECHO

......................... Switches on or off echo output of Control Change messages. 

(If this function is on, Control Change messages received from 
an external device will be retransmitted without modification.)

5

CONTROL CHANGE MODE field

This field enables you to select the Control Change transmission/reception mode.

•

NRPN button

............. If this button is on, the QL mix parameters will be transmitted/

received as NRPN messages on one MIDI channel (NRPN 
mode).

•

TABLE button

........... If this button is on, the QL mix parameters will be transmitted/

received as Control Change messages on one MIDI channel 
(TABLE mode).

6

PARAMETER CHANGE field

Enables you to turn transmission/reception of SysEx (system exclusive) messages on or 
off. (These are special messages used to control the parameter of the QL console.)

•

Tx

............................... Switches parameter change transmission on/off.

•

Rx

.............................. Switches parameter change reception on/off.

•

ECHO

......................... Switches on or off echo output of Parameter Change 

messages. (If this function is on, Parameter Change messages 
received from an external device will be retransmitted without 
modification.)

7

OTHER COMMMAND field

Switches on or off echo output of other MIDI messages. (If this function is on, other 
MIDI messages received from an external device will be retransmitted without 
modification.)

1

2

4

6

7

3

5

Содержание QL5







































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для QL5

MAKINEX MS-100 Operator'S Manual preview
MS-100
Бренд: MAKINEX Страницы: 16
Yamaha MW10 Mode D'Emploi preview
MW10
Бренд: Yamaha Страницы: 36
Valeton GP-100 Firmware Update Manual preview
GP-100
Бренд: Valeton Страницы: 2
Hamilton Beach Drink Master User Manual preview
Drink Master
Бренд: Hamilton Beach Страницы: 5
Hamilton Beach 64650 Read Before Use preview
64650
Бренд: Hamilton Beach Страницы: 20
Hamilton Beach 62630 Instructions Manual preview
62630
Бренд: Hamilton Beach Страницы: 8
Concept2 SM3500 Manual preview
SM3500
Бренд: Concept2 Страницы: 49
Harman Studer Micro Series Operating Instructions Manual preview
Studer Micro Series
Бренд: Harman Страницы: 111
Alesis iMultiMix 16 USB Reference Manual preview
iMultiMix 16 USB
Бренд: Alesis Страницы: 44
A.G. PULIE Easymix TU-MIX Operating Instructions Manual preview
Easymix TU-MIX
Бренд: A.G. PULIE Страницы: 7
jobmate HCM550 Owner'S Manual preview
HCM550
Бренд: jobmate Страницы: 11
ARDES PAIOLO Instructions For Use Manual preview
PAIOLO
Бренд: ARDES Страницы: 31
H.Koenig KM80 Instruction Manual preview
KM80
Бренд: H.Koenig Страницы: 56
Gecko Exodus Alpha MXR 1800 Owner'S Manual preview
Exodus Alpha MXR 1800
Бренд: Gecko Страницы: 26
Sunbeam Mixmaster 2379-33 User Manual preview
Mixmaster 2379-33
Бренд: Sunbeam Страницы: 2
PuzzleSounds SFT DISTORTION Manual preview
SFT DISTORTION
Бренд: PuzzleSounds Страницы: 17
PuzzleSounds DEEP BLUE DELAY Manual preview
DEEP BLUE DELAY
Бренд: PuzzleSounds Страницы: 17
Melissa 646-049 User Manual preview
646-049
Бренд: Melissa Страницы: 16

Бренды по названию

Популярные бренды

Загрузить еще бренды