Yamaha FZ6 Скачать руководство пользователя | Manualshive

Страница: 20 / 108

background image

INSTRUMENT AND CONTROL FUNCTIONS

3-2

3

EAU11003

Indicator and warning lights

EAU11030

Turn signal indicator lights “

”

and “

”

The corresponding indicator light flash-
es when the turn signal switch is
pushed to the left or right.

EAU11060

Neutral indicator light “

”

This indicator light comes on when the
transmission is in the neutral position.

EAU11080

High beam indicator light “

”

This indicator light comes on when the
high beam of the headlight is switched
on.

EAU11250

Oil level warning light “

”

This warning light comes on when the
engine oil level is low.
The electrical circuit of the warning light
can be checked by turning the key to
“ON”.
If the warning light does not come on
for a few seconds, then go off, have a
Yamaha dealer check the electrical cir-
cuit.

NOTE:

●

Even if the oil level is sufficient, the
warning light may flicker when
riding on a slope or during sudden
acceleration or deceleration, but
this is not a malfunction.

●

This model is also equipped with a
self-diagnosis device for the oil
level detection circuit. If the oil lev-
el detection circuit is defective, the
following cycle will be repeated un-
til the malfunction is corrected: The

oil level warning light will flash ten
times, then go off for 2.5 seconds.
If this occurs, have a Yamaha
dealer check the vehicle.

EAU11423

Coolant temperature warning
light “

”

This warning light comes on when the
engine overheats. When this occurs,
stop the engine immediately and allow
the engine to cool.
The electrical circuit of the warning light
can be checked by turning the key to
“ON”.
If the warning light does not come on
for a few seconds, then go off, have a
Yamaha dealer check the electrical cir-
cuit.

CAUTION:

ECA10020

Do not operate the engine if it is
overheated.

1. Left turn signal indicator light “

”

2. Right turn signal indicator light “

”

3. Neutral indicator light “

”

4. High beam indicator light “

”

5. Engine trouble warning light “

”

6. Oil level warning light “

”

7. Coolant temperature warning light “

”

U4S811E0.book Page 2 Wednesday, August 8, 2007 1:14 PM

«
...
18
19
20
21
22
...
»

Содержание FZ6













































































































Отзывы:

Нет отзывов

Похожие инструкции для FZ6

Бренд: Rally Pack Страницы: 2

Бренд: Yamaha Страницы: 860

Бренд: Öhlins Страницы: 2

Mechatronics 35007-01

Бренд: Öhlins Страницы: 4

McPherson Strut MIR 5H02

Бренд: Öhlins Страницы: 2

Бренд: Öhlins Страницы: 4

Бренд: Ducati Страницы: 128

Бренд: Nolan Страницы: 24

Rocky Mountain-EXP SB-1

Бренд: Wolfman Страницы: 7

B40 VICTOR W D 1967

Бренд: BSA Страницы: 128

Бренд: BMW Motorrad Страницы: 261

Бренд: hepco & becker Страницы: 4

Бренд: Arai Helmet Страницы: 12

Бренд: TM Страницы: 80

Бренд: Ermax Страницы: 2

Бренд: RIEJU Страницы: 39

Бренд: RIEJU Страницы: 51

Бренд: Vetter Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды