Yamaha FZ6 Скачать руководство пользователя страница 73

Страница: 73 / 108

PERIODIC MAINTENANCE AND MINOR REPAIR

6-31

EAU23212

Checking and lubricating the
centerstand and sidestand

The operation of the centerstand and
sidestand should be checked before
each ride, and the pivots and metal-to-
metal contact surfaces should be lubri-
cated if necessary.

WARNING

EWA10740

If the centerstand or sidestand does
not move up and down smoothly,
have a Yamaha dealer check or re-
pair it.

EAUM1650

Lubricating the swingarm piv-
ots

The swingarm pivots must be lubricat-
ed at the intervals specified in the peri-
odic maintenance and lubrication chart.

Recommended lubricants:

Brake lever:

Silicone grease

Clutch lever:

Lithium-soap-based grease

Recommended lubricant:

Lithium-soap-based grease

Recommended lubricant:

Lithium-soap-based grease

U4S811E0.book Page 31 Wednesday, August 8, 2007 1:14 PM

Содержание FZ6













































































































Результаты поиска

Содержание FZ6

Отзывы:

Бренды по названию

Популярные бренды

Yamaha FZ6, Руководство пользователя

Результаты поиска

Содержание FZ6

Отзывы:

Бренды по названию

Популярные бренды