Yamaha FZ6 Скачать руководство пользователя

Страница: 64 / 108

PERIODIC MAINTENANCE AND MINOR REPAIR

6-22

WARNING

EWA10580

●

It is dangerous to ride with a
worn-out tire. When a tire tread
begins to show crosswise lines,
have a Yamaha dealer replace
the tire immediately.

●

The replacement of all wheel-
and brake-related parts, includ-
ing the tires, should be left to a
Yamaha dealer, who has the
necessary professional knowl-
edge and experience.

Tire information

This motorcycle is equipped with cast
wheels and tubeless tires with valves.

WARNING

EWA10480

●

The front and rear tires should
be of the same make and de-
sign, otherwise the handling
characteristics of the motor-
cycle cannot be guaranteed.

●

After extensive tests, only the
tires listed below have been ap-
proved for this model by
Yamaha Motor Co., Ltd.

●

Always make sure that the valve
caps are securely installed to
prevent air pressure leakage.

●

Use only the tire valves and
valve cores listed below to
avoid tire deflation during a
high-speed ride.

WARNING

EWA10600

This motorcycle is fitted with super-
high-speed tires. Note the following
points in order to make the most ef-
ficient use of these tires.

●

Use only the specified replace-
ment tires. Other tires may run
the danger of bursting at super
high speeds.

●

Brand-new tires can have a rela-
tively poor grip on certain road
surfaces until they have been

1. Tire air valve
2. Tire air valve core

3. Tire air valve cap with seal

Front tire:

Size:

120/70 ZR17M/C (58W)

Manufacturer/model:

BRIDGESTONE/BT020F GG
DUNLOP/D252F

Rear tire:

Size:

180/55 ZR17M/C (73W)

Manufacturer/model:

BRIDGESTONE/BT020R GG
DUNLOP/D252

FRONT and REAR:

Tire air valve:

TR412

Valve core:

#9100 (original)

U4S811E0.book Page 22 Wednesday, August 8, 2007 1:14 PM

Содержание FZ6













































































































Результаты поиска

Содержание FZ6

Отзывы:

Похожие инструкции для FZ6

Бренды по названию

Популярные бренды

Yamaha FZ6, Руководство пользователя

Результаты поиска

Содержание FZ6

Отзывы:

Похожие инструкции для FZ6

Бренды по названию

Популярные бренды