Yamaha FZ6 Скачать руководство пользователя | Manualshive

Страница: 40 / 108

background image

OPERATION AND IMPORTANT RIDING POINTS

5-2

5

CAUTION:

ECA15490

●

If the oil level warning light flick-
ers or remains on after starting,
immediately stop the engine,
and then check the engine oil
level and the vehicle for oil leak-
age. If necessary, add engine
oil, and then check the warning
light again.

●

If the coolant temperature warn-
ing light flickers or remains on
after starting, immediately stop
the engine, and then check the
coolant level and the vehicle for
coolant leakage. If necessary,
add coolant, and then check the
warning light again.

●

If the engine trouble warning
light flashes or remains on after
starting, immediately stop the
engine, and have a Yamaha
dealer check the cause.

CAUTION:

ECA11130

For maximum engine life, always
warm the engine up before starting
off. Never accelerate hard when the
engine is cold!

EAU16671

Shifting

Shifting gears lets you control the
amount of engine power available for
starting off, accelerating, climbing hills,
etc.
The gear positions are shown in the il-
lustration.

NOTE:

To shift the transmission into the neu-
tral position, press the shift pedal down
repeatedly until it reaches the end of its
travel, and then slightly raise it.

1. Shift pedal

2. Neutral position

U4S811E0.book Page 2 Wednesday, August 8, 2007 1:14 PM

«
...
38
39
40
41
42
...
»

Содержание FZ6













































































































Отзывы:

Нет отзывов

Похожие инструкции для FZ6

Бренд: KAYO MOTOR Страницы: 84

Бренд: DAELIM Страницы: 93

640 LC4 ENDURO 2006

Бренд: KTM Страницы: 60

Бренд: hepco & becker Страницы: 4

Бренд: N-Com Страницы: 32

Бренд: Triumph Страницы: 53

California EV V1100

Бренд: MOTO GUZZI Страницы: 173

Бренд: Vance and hines Страницы: 5

Бренд: Honda Страницы: 180

Бренд: Yamaha Страницы: 26

Бренд: Yamaha Страницы: 58

Бренд: Yamaha Страницы: 42

Бренд: Yamaha Страницы: 92

Бренд: Yamaha Страницы: 77

Бренд: Yamaha Страницы: 106

Бренд: Yamaha Страницы: 88

Бренд: Yamaha Страницы: 112

Бренд: Yamaha Страницы: 90

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды