Yamaha FZ6 Скачать руководство пользователя | Manualshive

Страница: 24 / 108

background image

INSTRUMENT AND CONTROL FUNCTIONS

3-6

3

eter display will automatically change to
the fuel reserve tripmeter mode “F-
TRIP” and start counting the distance
traveled from that point. In that case,
push the “SELECT” button to switch the
display between the various tripmeter
and odometer modes in the following
order:
F-TRIP

→

TRIP A

→

TRIP B

→

ODO

→

F-TRIP

To reset a tripmeter, select it by push-
ing the “SELECT” button, and then
push the “RESET” button for at least
one second. If you do not reset the fuel
reserve tripmeter manually, it will reset
itself automatically and the display will
return to the prior mode after refueling
and traveling 5 km (3 mi).

Fuel meter

The fuel meter indicates the amount of
fuel in the fuel tank. The display seg-
ments of the fuel meter disappear to-
wards “E” (Empty) as the fuel level
decreases. When the last segment on
the left starts flashing, refuel as soon as
possible.

NOTE:

This fuel meter is equipped with a self-
diagnosis system. If the electrical circuit
is defective, the following cycle will be
repeated until the malfunction is cor-
rected: “E” (Empty), “F” (Full) and
symbol “

” will flash eight times, then

go off for approximately 3 seconds. If
this occurs, have a Yamaha dealer
check the electrical circuit.

Coolant temperature mode

The coolant temperature display indi-
cates the temperature of the coolant.
Push the “RESET” button to switch the
coolant temperature display to the air
intake temperature display.

NOTE:

When the coolant temperature display
is selected, “C” is displayed for one
second, and then the coolant tempera-
ture is displayed.

1. Fuel meter

1. Coolant temperature display

U4S811E0.book Page 6 Wednesday, August 8, 2007 1:14 PM

«
...
22
23
24
25
26
...
»

Содержание FZ6













































































































Отзывы:

Нет отзывов

Похожие инструкции для FZ6

Бренд: Honda Страницы: 325

Бренд: Christopeit Sport Страницы: 16

Бренд: PUIG Страницы: 2

Бренд: Yamaha Страницы: 112

Бренд: Honda Страницы: 123

Бренд: Kemppi Страницы: 10

Бренд: Yamaha Страницы: 26

Бренд: Yamaha Страницы: 58

Бренд: Yamaha Страницы: 42

Бренд: Yamaha Страницы: 92

Бренд: Yamaha Страницы: 77

Бренд: Yamaha Страницы: 106

Бренд: Yamaha Страницы: 88

Бренд: Yamaha Страницы: 112

Бренд: Yamaha Страницы: 90

Star Venture 2018

Бренд: Yamaha Страницы: 116

Бренд: Yamaha Страницы: 92

Бренд: Yamaha Страницы: 108

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды