Yamaha FZ6 Скачать руководство пользователя | Manualshive

Страница: 35 / 108

background image

INSTRUMENT AND CONTROL FUNCTIONS

3-17

3

With the engine turned off:
1. Move the sidestand down.
2. Make sure that the engine stop switch is turned on.
3. Turn the key on.
4. Shift the transmission into the neutral position.
5. Push the start switch.

Does the engine start?

With the engine still running:
6. Move the sidestand up.
7. Keep the clutch lever pulled.
8. Shift the transmission into gear.
9. Move the sidestand down.

Does the engine stall?

After the engine has stalled:
10. Move the sidestand up.
11. Keep the clutch lever pulled.
12. Push the start switch.

Does the engine start?

The system is OK.

The motorcycle can be ridden.

The neutral switch may be defective.

The motorcycle should not be ridden

until

checked by a Yamaha dealer.

The sidestand switch may be defective.

The motorcycle should not be ridden

until

checked by a Yamaha dealer.

The clutch switch may be defective.

The motorcycle should not be ridden

until

checked by a Yamaha dealer.

YES

NO

YES

NO

YES

NO

U4S811E0.book Page 17 Wednesday, August 8, 2007 1:14 PM

«
...
33
34
35
36
37
...
»

Содержание FZ6













































































































Отзывы:

Нет отзывов

Похожие инструкции для FZ6

Versaflo M Series

Бренд: 3M Страницы: 27

Speedglas 9100 Series

Бренд: 3M Страницы: 2

Бренд: 3M Страницы: 5

Бренд: BMW Страницы: 245

Бренд: RPS Страницы: 28

Бренд: Cycle Protect Страницы: 15

Бренд: Eastwood Страницы: 8

Бренд: X-lite Страницы: 33

Бренд: DYNATEK Страницы: 2

Бренд: Yamaha Страницы: 26

Бренд: Yamaha Страницы: 58

Бренд: Yamaha Страницы: 42

Бренд: Yamaha Страницы: 92

Бренд: Yamaha Страницы: 77

Бренд: Yamaha Страницы: 106

Бренд: Yamaha Страницы: 88

Бренд: Yamaha Страницы: 112

Бренд: Yamaha Страницы: 90

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды