Yamaha FZ6 Скачать руководство пользователя

Страница: 34 / 108

INSTRUMENT AND CONTROL FUNCTIONS

3-16

below and have a Yamaha dealer re-
pair it if it does not function proper-
ly.

EAU44900

Ignition circuit cut-off system

The ignition circuit cut-off system (com-
prising the sidestand switch, clutch
switch and neutral switch) has the fol-
lowing functions.

●

It prevents starting when the trans-
mission is in gear and the side-
stand is up, but the clutch lever is
not pulled.

●

It prevents starting when the trans-
mission is in gear and the clutch le-
ver is pulled, but the sidestand is
still down.

●

It cuts the running engine when the
transmission is in gear and the sid-
estand is moved down.

Periodically check the operation of the
ignition circuit cut-off system according
to the following procedure.

WARNING

EWA10260

●

The vehicle must be placed on
the centerstand during this in-
spection.

●

If a malfunction is noted, have a
Yamaha dealer check the sys-
tem before riding.

U4S811E0.book Page 16 Wednesday, August 8, 2007 1:14 PM

Содержание FZ6













































































































Результаты поиска

Содержание FZ6

Отзывы:

Похожие инструкции для FZ6

Бренды по названию

Популярные бренды

Yamaha FZ6, Руководство пользователя

Результаты поиска

Содержание FZ6

Отзывы:

Похожие инструкции для FZ6

Бренды по названию

Популярные бренды