Yamaha FZ6 Скачать руководство пользователя страница 77

Страница: 77 / 108

PERIODIC MAINTENANCE AND MINOR REPAIR

6-35

EAU32842

Replacing the fuses

The main fuse is located under the fuel
tank. (See page 6-18.)

The fuse box is located behind panel C.
(See page 6-9.)

If a fuse is blown, replace it as follows.

1. Turn the key to “OFF” and turn off

the electrical circuit in question.

2. Remove the blown fuse, and then

install a new fuse of the specified
amperage.

CAUTION:

ECA10640

Do not use a fuse of a higher amper-
age rating than recommended to
avoid causing extensive damage to
the electrical system and possibly a
fire.

3. Turn the key to “ON” and turn on

the electrical circuit in question to
check if the device operates.

4. If the fuse immediately blows

again, have a Yamaha dealer
check the electrical system.

1. Main fuse

2. Spare main fuse

1. Fuse box

1. Headlight fuse
2. Signaling system fuse

3. Ignition fuse

4. Radiator fan fuse
5. Backup fuse (for odometer and clock)

6. Fuel injection system fuse

7. Spare fuse
8. Taillight fuse

Specified fuses:

Main fuse:

30.0 A

Headlight fuse:

20.0 A

Taillight fuse:

10.0 A

Signaling system fuse:

10.0 A

Ignition fuse:

10.0 A

Radiator fan fuse:

20.0 A

Fuel injection system fuse:

10.0 A

Backup fuse:

10.0 A

U4S811E0.book Page 35 Wednesday, August 8, 2007 1:14 PM

Содержание FZ6













































































































Результаты поиска

Содержание FZ6

Отзывы:

Бренды по названию

Популярные бренды

Yamaha FZ6, Руководство пользователя

Результаты поиска

Содержание FZ6

Отзывы:

Бренды по названию

Популярные бренды