Yamaha FZ6 Скачать руководство пользователя | Manualshive

Страница: 65 / 108

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-23

6

“broken in”. Therefore, it is ad-
visable before doing any high-
speed riding to ride conserva-
tively for approximately 100 km
(60 mi) after installing a new tire.

●

The tires must be warmed up
before a high-speed run.

●

Always adjust the tire air pres-
sure according to the operating
conditions.

EAU21960

Cast wheels

To maximize the performance, durabil-
ity, and safe operation of your vehicle,
note the following points regarding the
specified wheels.

●

The wheel rims should be checked
for cracks, bends or warpage be-
fore each ride. If any damage is
found, have a Yamaha dealer re-
place the wheel. Do not attempt
even the smallest repair to the
wheel. A deformed or cracked
wheel must be replaced.

●

The wheel should be balanced
whenever either the tire or wheel
has been changed or replaced. An
unbalanced wheel can result in
poor performance, adverse han-
dling characteristics, and a short-
ened tire life.

●

Ride at moderate speeds after
changing a tire since the tire sur-
face must first be “broken in” for it
to develop its optimal characteris-
tics.

EAU22011

Accessories and replacement
parts

WARNING

EWA10621

This vehicle is not designed to pull a
trailer or to be attached to a sidecar.
The accessories or replacement
parts you choose for your vehicle
should be designed specifically for
this model, and they must be se-
curely mounted to maintain the in-
herent stability of the original
design. Genuine Yamaha Parts and
Accessories are designed and test-
ed to be compatible with your vehi-
cle. Please consider Genuine
Yamaha Parts and Accessories be-
fore making a purchase. Use of non-
Yamaha-approved accessories or
replacement parts may cause loss of
handling stability and riding safety.
Since Yamaha cannot control the
quality of accessories or parts man-
ufactured by other companies,
Yamaha cannot be held liable for

U4S811E0.book Page 23 Wednesday, August 8, 2007 1:14 PM

«
...
63
64
65
66
67
...
»

Содержание FZ6













































































































Отзывы:

Нет отзывов

Похожие инструкции для FZ6

Бренд: Sachs Bikes Страницы: 71

Бренд: R&G Страницы: 6

Бренд: A.J.S. Страницы: 104

RACE 13100CP520

Бренд: Yoshimura Страницы: 7

Бренд: Victory Motorcycles Страницы: 332

SUPERSPORT1000 2003

Бренд: Ducati Страницы: 328

Бренд: Yamaha Страницы: 98

Бренд: Yamaha Страницы: 116

Tracer 9 GT 2021

Бренд: Yamaha Страницы: 126

Бренд: Yamaha Страницы: 116

Бренд: Yamaha Страницы: 106

Бренд: Yamaha Страницы: 116

Бренд: Yamaha Страницы: 87

Бренд: DYNATEK Страницы: 4

ZIEGER 10005243

Бренд: IBEX Страницы: 4

Бренд: Dayi Motor Страницы: 18

VarioProtect PANORAMA-W R-TC

Бренд: Schweißkraft Страницы: 22

Бренд: Sealey Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды