Yamaha F250B Скачать руководство пользователя

Страница: 80 / 122

Operation

Remove the key if the boat will be left un-
attended.

TIP:

The engine can also be stopped by pulling the
cord and removing the clip from the engine
shut-off switch, then turning the main switch
to “

” (off).

EMU35930

Procedure for dual station models
(main station)

The procedure until stopping the engine
is the same as that of the single station
models.

Remove the key if the boat will be left un-
attended.

TIP:

The engine can also be stopped by pulling the
cord and removing the clip from the engine
shut-off switch, then turning the main switch
to “

” (off).

EMU35910

Procedure for dual station models
(sub station)

Push and hold the red engine stop button until
the engine comes to a complete stop. When
the engine has been stopped from the sub
station, be sure to turn the main switch on the
main station to “

”.

TIP:

The engine can also be stopped by pulling the
engine shut-off cord and removing the clip
from the engine shut-off switch.

EMU27862

Trimming outboard motor

WARNING

EWM00740

Excessive trim for the operating condi-
tions (either trim up or trim down) can
cause boat instability and can make steer-

OFF

ZMU06014

ZMU05986

ZMU05987

ZMU05988

U6BR11E0.book Page 74 Friday, June 13, 2008 3:43 PM

2019 Yamaha Motor Corporation, U.S.A.

Содержание F250B



























































































































Результаты поиска

Содержание F250B

Отзывы:

Похожие инструкции для F250B

Бренды по названию

Популярные бренды

Yamaha F250B, Руководство пользователя

Результаты поиска

Содержание F250B

Отзывы:

Похожие инструкции для F250B

Бренды по названию

Популярные бренды