manualshive.com logo in svg

Yamaha F250B, Руководство пользователя

Поделиться
Скачать
Yamaha F250B Скачать руководство пользователя страница 44

Components

38

NOTICE

ECM00840

The trim tab also serves as an anode to
protect the engine from electrochemical
corrosion. Never paint the trim tab as it will
become ineffective as an anode.

EMU26341

Tilt support lever for power trim and 
tilt model

To keep the outboard motor in the tilted up po-
sition, lock the tilt support lever to the clamp
bracket.

NOTICE

ECM00660

Do not use the tilt support lever or knob
when trailering the boat. The outboard mo-
tor could shake loose from the tilt support
and fall. If the motor cannot be trailered in
the normal running position, use an addi-
tional support device to secure it in the tilt
position.

EMU31420

Top cowling lock lever (pull up type)

To remove the top cowling, pull up the lock le-
ver(s) and lift off the cowling. To install the top
cowling, place it in its original position, and
then move the lever(s) downward to lock it in
place.

1. Trim tab
2. Bolt

3. Cap

Bolt tightening torque:

42.0 Nm (4.28 kgf-m, 31.0 ft-lb)

U6BR11E0.book  Page 38  Friday, June 13, 2008  3:43 PM

©

2019 Yamaha Motor Corporation, U.S.A.

Содержание F250B



























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды