Yamaha F250B Скачать руководство пользователя | Manualshive

Страница: 42 / 122

background image

Components

36

Twin type

Triple type

EMU35152

Power trim and tilt switch on digital
electronic control

The power trim and tilt system adjusts the out-
board motor angle in relation to the transom.
Pressing the switch “

” (up) trims the out-

board motor up, and then tilts it up. Pressing
the switch “

” (down) tilts the outboard motor

down and trims it down. When the switch is re-
leased, the outboard motor will stop in its cur-
rent position. For instructions on using the
power trim and tilt switch, see pages 74 and
77.

EMU26153

Power trim and tilt switch on bottom
engine cowling

The power trim and tilt switch is located on the
side of the bottom engine cowling. Pressing
the switch “

” (up) trims the outboard motor

up, and then tilts it up. Pressing the switch
“

” (down) tilts the outboard motor down and

trims it down. When the switch is released,
the outboard motor will stop in its current po-
sition.
For instructions on using the power trim and
tilt switch, see page 77.

WARNING

EWM01030

Use the power trim and tilt switch located
on the bottom engine cowling only when
the boat is at a complete stop with the en-
gine off. Attempting to use this switch
while the boat is moving could increase

ZMU05987

ZMU05988

ZMU06234

UP

DN

ZMU05822

UP

DN

U6BR11E0.book Page 36 Friday, June 13, 2008 3:43 PM

©

2019 Yamaha Motor Corporation, U.S.A.

«
...
40
41
42
43
44
...
»

Содержание F250B



























































































































Отзывы:

Нет отзывов

Похожие инструкции для F250B

Бренд: Acer Страницы: 12

Бренд: Linear Technology Страницы: 16

Бренд: BIGTREETECH Страницы: 39

IONITX-N series

Бренд: Zotac Страницы: 50

VECTOR 1 MOTHERBOARD

Бренд: Vector Graphic Страницы: 14

Бренд: ISSC Страницы: 39

Бренд: IEI Technology Страницы: 156

Бренд: MSI Страницы: 104

Бренд: EPC Страницы: 10

NuMaker NUC980 IIoT

Бренд: Nuvoton Страницы: 46

Super 7 SY-5SSM

Бренд: SOYO Страницы: 86

Бренд: IDT Страницы: 5

Бренд: ASROCK Страницы: 4

Бренд: MSI Страницы: 58

Бренд: DFI Страницы: 105

Бренд: Gigabyte Страницы: 40

Бренд: Consumer Microcircuits Страницы: 58

Minix780G Series

Бренд: J&W Страницы: 41

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды