manualshive.com logo in svg

Yamaha F250B, Руководство пользователя

Поделиться
Скачать
Yamaha F250B Скачать руководство пользователя страница 68

Operation

62

5.

Immediately after the engine starts, re-
lease the main switch to return it to “

”

(on). 

NOTICE:

 Never turn the main

switch to “

” (start) while the en-

gine is running. Do not keep the start-
er motor turning for more than 5
seconds. If the starter motor is turned
continuously for more than 5 sec-
onds, the battery will be quickly dis-
charged, thus making it impossible to
start the engine. The starter can also
be damaged. If the engine will not start
after 5 seconds of cranking, return the
main switch to “

” (on), wait 10 sec-

onds, then crank the engine again.

[ECM00192]

EMU35922

Procedure for dual station models (main
station)

1.

Place the control lever in “ ” (neutral).

TIP:

The start-in-gear protection device prevents
the engine from starting except when in neu-
tral.

2.

Turn the main switch “

”  (on)  to  make

sure that the digital electronic control-ac-
tive indicator lights. The engine can not
be started when the digital electronic con-
trol-alert indicator lights.

3.

The procedure until starting the engine is
the same as that of the single station
models. 

NOTICE:

 Never turn the main

switch to “

” (start) while the en-

gine is running. Do not keep the start-
er motor turning for more than 5
seconds. If the starter motor is turned
continuously for more than 5 sec-
onds, the battery will be quickly dis-
charged, thus making it impossible to
start the engine. The starter can also
be damaged. If the engine will not start

ON

START

ZMU05830

ON

START

ZMU05994

ZMU05829

N

U6BR11E0.book  Page 62  Friday, June 13, 2008  3:43 PM

©

2019 Yamaha Motor Corporation, U.S.A.

Содержание F250B



























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды