manualshive.com logo in svg

Yamaha F250B, Руководство пользователя

Поделиться
Скачать
Yamaha F250B Скачать руководство пользователя страница 60

Operation

54

NOTICE

ECM00120

Do not start the engine out of water. Over-
heating and serious engine damage can
occur.

EMU36420

Fuel level

Be sure you have plenty of fuel for your trip. A
good rule is to use 1/3 of your fuel to get to the
destination, 1/3 to return, and to keep 1/3 as
an emergency reserve. With the boat level on
a trailer or in the water, turn the key to
“

”(on) and check the fuel level. For fuel fill-

ing instructions, see page 59.

EMU36431

Remove cowling

For the following checks, remove the top
cowling from the engine. To remove the en-
gine cowling, release all the lock levers and lift
off the cowling.

EMU36442

Fuel system

WARNING

EWM00060

Gasoline and its vapors are highly flam-
mable and explosive. Keep away from
sparks, cigarettes, flames, or other sourc-
es of ignition.

WARNING

EWM00910

Leaking fuel can result in fire or explosion.

●

Check for fuel leakage regularly.

●

If any fuel leakage is found, the fuel sys-
tem must be repaired by a qualified me-
chanic. Improper repairs can make the
outboard unsafe to operate.

EMU36450

Check for fuel leaks

●

Check under top cowling and in the boat for
fuel leaks or gasoline fumes.

●

Check fuel line connections to be sure they
are tight.

●

Check fuel lines for cracks, swelling, or oth-
er damage.

EMU37320

Check the fuel filter

Check that the fuel filter is clean and free of
water. If any water is found in the fuel, or if a
significant amount of debris is found, the fuel
tank should be checked and cleaned by a
Yamaha dealer.

ZMU06106

ZMU06108

U6BR11E0.book  Page 54  Friday, June 13, 2008  3:43 PM

©

2019 Yamaha Motor Corporation, U.S.A.

Содержание F250B



























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды