Yamaha F250B Скачать руководство пользователя | Manualshive

Страница: 113 / 122

background image

Trouble Recovery

107

EMU29524

Power trim and tilt will not operate

If the engine cannot be tilted up or down with
the power trim and tilt because of a dis-
charged battery or a failure with the power
trim and tilt unit, the engine can be tilted man-
ually.
1.

Loosen the manual valve screw by turn-
ing it counterclockwise until it stops.

2.

Put the engine in the desired position,
then tighten the manual valve screw by
turning it clockwise.

EMU31593

Water separator-alert indicator blinks
while cruising

WARNING

EWM01500

Gasoline is highly flammable, and its va-
pors are flammable and explosive.

●

Do not perform this procedure on a hot
or running engine. Allow the engine to
cool.

●

There will be fuel in the fuel filter. Keep
away from sparks, cigarettes, flames or
other sources of ignition.

●

This procedure will allow some fuel to
spill. Catch fuel in a rag. Wipe up any
spilled fuel immediately.

●

The fuel filter must be reassembled
carefully with the O-ring, filter cup, and
hoses in place. Improper assembly or
replacement could result in a fuel leak,
which could result in a fire or explosion
hazard.

If the water separator-alert indicator on the
Command Link tachometer blinks, perform
the following procedure.

1.

Stop the engine.

2.

Remove the top cowling.

3.

Remove the holder.

8. Engine main fuse (60 A)
9. Isolator fuse (60 A)

1. Manual valve screw

1

ZMU01905

1. Water separator-alert indicator

U6BR11E0.book Page 107 Friday, June 13, 2008 3:43 PM

©

2019 Yamaha Motor Corporation, U.S.A.

«
...
111
112
113
114
115
...
»

Содержание F250B



























































































































Отзывы:

Нет отзывов

Похожие инструкции для F250B

Бренд: DFI Страницы: 99

Бренд: Texas Instruments Страницы: 101

Бренд: Arbor Technology Страницы: 86

Бренд: Biostar Страницы: 37

dsPICDEM MCHV-3

Бренд: Microchip Technology Страницы: 68

Бренд: Norco Страницы: 55

Бренд: Diodes Страницы: 7

Бренд: DFI Страницы: 28

Бренд: Advantech Страницы: 124

Бренд: Maxtang Страницы: 14

Бренд: Supermicro Страницы: 97

Бренд: Dell Страницы: 27

S870 EXTREME3QVL - LIST

Бренд: ASROCK Страницы: 3

Бренд: Zotac Страницы: 62

Бренд: Asus Страницы: 57

Бренд: Asus Страницы: 54

Бренд: Asus Страницы: 57

P8H61-M LX PLUS R2.0

Бренд: Asus Страницы: 66

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды