manualshive.com logo in svg

Yamaha F250B, Руководство пользователя

Поделиться
Скачать
Yamaha F250B Скачать руководство пользователя страница 98

Maintenance

92

5.

When fitting the plug, wipe off any dirt
from the threads, and then screw it in to
the correct torque.

TIP:

If a torque-wrench is not available when you
are fitting a spark plug, a good estimate of the
correct torque is 1/4 to 1/2 turn past finger-
tight. Have the spark plug adjusted to the cor-
rect torque as soon as possible with a torque-
wrench.
6.

Install the ignition coil and tighten the
bolts.

7.

Install the ECM (Electronic control mod-
ule) cover and tighten the bolts.

EMU35270

Inspecting idling speed

NOTICE

ECM01690

This procedure must be performed while
the outboard motor is in the water.

Perform this procedure using the Command
Link Tachometer. Results may vary depend-
ing on whether testing is conducted with the
outboard motor in the water.
1.

Start the engine and allow it to warm up
fully in neutral until it is running smoothly.

2.

Verify whether the idle speed is set to
specification. For idle speed specifica-
tions, see page 14.

EMU37482

Changing engine oil

NOTICE

ECM01710

Change the engine oil after the first 20
hours of operation or 3 months, and every
100 hours or at 1-year intervals thereafter.
Otherwise the engine will wear quickly.

The engine oil should be extracted with an oil
changer.
1.

Put the outboard motor in an upright po-
sition (not tilted). 

NOTICE:

 If the motor

is not level, the oil level indicated on
the dipstick may not be accurate.

[ECM01860]

1. Spark plug gap

2. Spark plug part number

3. Spark plug I.D. mark (NGK)

Spark plug gap:

1.0–1.1 mm (0.039–0.043 in)

Spark plug torque:

25.0 Nm (2.55 kgf-m, 18.4 ft-lb)

Bolt tightening torque:

7.0 Nm (0.71 kgf-m, 5.2 ft-lb)

Bolt tightening torque:

8.0 Nm (0.82 kgf-m, 5.9 ft-lb)

U6BR11E0.book  Page 92  Friday, June 13, 2008  3:43 PM

©

2019 Yamaha Motor Corporation, U.S.A.

Содержание F250B



























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды