Yaesu FT1DR Скачать руководство пользователя страница 5

Страница: 5 / 156

Read this information first

Introduction

Features of the FT1DR/DE

Digital communication (C4FM (Quaternary FSK), FDMA system) ............................. 31

Equipped with AMS (Automatic Mode Select) Function ............................................. 32

Automatically selects between 4 modes of transmission to fit the signal being
received.

External power supply connection ............................................................................. 20

Simultaneous reception on two different bands, or within the same band (V+V/U+U)

................................................................................................................................... 28

Independent switching keys for A-band and B-band and TX/BUSY display .............. 28

Wide-band reception over the range of 500 kHz to 999.900MHz .............................. 28

Waterproof design conforming to IPX5 equivalent, which protects the transceiver

from rain and splashes ............................................................................................... 11

Individual side keys, full keyboard for easy character entry, tilted main dials ............ 12

Easy-to-see dot matrix display ................................................................................... 14

WIRES-X connection support ..................................See WIRES-X instruction manual*

Equipped with GM function ..................................See GM function instruction manual*

Large-capacity 1266ch memory, with twenty-four 100ch memory banks .................. 42

Display memory tags comprised of up to 16 one-byte characters ............................. 46

Convenient reception of preset receiver memory channels ....................................... 51

By selecting preset frequencies, you can receive shortwave broadcast,

and

international VHF radio stations with ease.

A wide variety of scan functions ................................................................................. 56

Built-in GPS unit allowing display of your current location and heading

information ................................................................................................................. 68

Ready for APRS

communication using the world standard 1200/ 9600bps AX25

modem (B band only) ................................................... See APRS instruction manual.*

High-resolution band scope function to display ± 50 channels .................................. 82

A variety of individual selective calling functions; such as tone squelch (CTCSS)

and DCS functions ..................................................................................................... 84

Vibrator to alert you of signal reception, in addition to the audible bell ...................... 88

New pager function for calling only specific stations .................................................. 90

Illumination by white LED for easy viewing of the LCD outdoors ............................. 129

Built-in temperature sensor ...................................................................................... 108

Battery save function to prolong the operating time of the battery ........................... 135

Data terminal for communication with external equipment or firmware

update

...................................................................................................................... 143

Built-in bar antenna for AM reception ......................................................................... 33

Micro SD memory card slot ........................................................................................ 22

Snapshot function (an optional camera microphone MH-85A11U is required) .......... 82

* WIRES-X, GM function and APRS instruction manuals are not included in the product

package.

They are available and may be downloaded from the Yaesu.com website.
Please download the WIRES-X function instruction manual from our home page when

it is released.

FT1DR̲DE̲Eng.indb 5

13/06/28 15:15

Содержание FT1DR





























































































































































Результаты поиска

Содержание FT1DR

Отзывы:

Похожие инструкции для FT1DR

Бренды по названию

Популярные бренды

Yaesu FT1DR, Руководство по эксплуатации

Результаты поиска

Содержание FT1DR

Отзывы:

Похожие инструкции для FT1DR

Бренды по названию

Популярные бренды