Yaesu FT1DR Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 156

background image

15

Basic Operation

Basic Operation

Preparation

Installing the Antenna

1

Align the antenna with the antenna terminal on the transceiver.

Caution

Be sure to hold the thick base of the antenna when installing it.

2

Turn the antenna clockwise until it is secured.

Cautions

z

Do not hold the upper part of the antenna when installing or removing it. To
do so, the wire inside the antenna may break.

z

Do not transmit without installing the antenna. The transmitter circuit can
be damaged.

z

When using an antenna other than the accessory or any other external
antenna, ensure that its SWR is adjusted to 1.5 or lower.

Attaching the Accessory Belt Clip/Protective Cap

Attaching the Protective Cap

1

Attach the protective cap

If you do not use the belt clip, attach the protective cap
to the belt clip attaching screw holes on the battery
pack.

Attaching the Belt Clip

1

Turn over the battery pack.

2

Attach the belt clip to the battery pack using the

supplied screws (two).

Cautions

z

Be sure to use the supplied screws when attaching the
belt clip. If any other screws are used. the belt clip cannot
be secured firmly to the battery pack and the transceiver
may drop off together with the battery pack, causing injury,
breakage and other troubles.

z

Be sure to attach the protective cap when the belt clip is not
used.

FT1DR̲DE̲Eng.indb 15

FT1DR̲DE̲Eng.indb 15

13/06/28 15:15

13/06/28 15:15

«
...
13
14
15
16
17
...
»

Содержание FT1DR





























































































































































Отзывы:

Нет отзывов

Похожие инструкции для FT1DR

Бренд: R&S Страницы: 232

Бренд: Vector Страницы: 5

Бренд: YouKits Страницы: 1

Бренд: Paul Wegener Страницы: 8

Бренд: Harman Kardon Страницы: 28

Бренд: WAC Lighting Страницы: 6

Бренд: Alinco Страницы: 71

GE-PON OLT Transceiver OPEP-33-B4K3R

Бренд: Delta Страницы: 8

Бренд: Yaesu Страницы: 20

Бренд: Vectronics Страницы: 26

Бренд: Dish Network Страницы: 26

Бренд: Optimus Страницы: 40

Бренд: Novus Страницы: 72

Бренд: National Страницы: 25

Бренд: DNT Страницы: 60

Бренд: Strong Страницы: 17

Бренд: gefran Страницы: 35

Beolit Teena 609 AM Export

Бренд: Bang & Olufsen Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды