Xylem ProSwap 610224-01 Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 116

Xylem ProSwap 610224-01 Скачать руководство пользователя страница 2

The information contained in this manual is subject to change without notice.

Effort has been made to make the information in this manual complete, accurate, and current.

The manufacturer shall not be held responsible for errors or omissions in this manual.

for the most up-to-date version of this manual.

A
A

NOTICE:

Indicates a situation which, if not avoided, may cause damage to the instrument

Thank you for purchasing a YSI ProSwap Logger. This manual covers setup, operation, and functionality of the sonde,
handheld, and sensors.

Product Components

Carefully unpack the instrument and accessories and inspect for damage. If any parts or materials are damaged,
contact YSI Customer Service at 800-897-4151 (+1 937 767-7241) or the authorized YSI distributor from whom the
instrument was purchased.

Technical Support

Telephone: 800 897 4151 (USA)
+1 937 767 7241 (Globally) Monday through Friday, 8:00 AM to 5:00 ET
Fax: +1 937 767 9353 (orders)
Email:

[email protected]

Safety Information

Please read this entire manual before unpacking, setting up or operating this equipment. Pay attention to all
precautionary statements. Failure to do so could result in serious injury to the operator or damage to the equipment.
Make sure that the protection provided by this equipment is not impaired. Do not use or install this equipment in any
manner other than that specified in this manual.

The manufacturer is not responsible for any damages due to misapplication or misuse of this product including,
without limitation, direct, incidental and consequential damages, and disclaims such damages to the full extent
permitted under applicable law. The user is solely responsible to identify critical application risks and install
appropriate mechanisms to protect processes during a possible equipment malfunction.

Precautionary Symbols

NOTE:

Information that requires special emphasis

WARNING:

Indicates a potentially or imminently hazardous situation which, if not avoided, could result in death
or serious injury

CAUTION:

Indicates a potentially hazardous situation that may result in minor or moderate injury

«
1
2
3
4
...
»

Содержание ProSwap 610224-01





















































































































Отзывы:

Нет отзывов